Bolt length calculation

Senast uppdaterad March 6, 2017 by Tekla User Assistance tekla.documentation@trimble.com

Programvaruversion: 
2017

Bolt length calculation

Bolt length calculation

Tekla Structures uses values from the bolt catalog and the bolt assembly catalog when calculating the bolt length. If the bolt catalog does not contain long enough bolts for your purposes, you need to add them to the bolt catalog.

The following settings in the Bolt Properties dialog box affect the bolt length calculation process. If the check box is selected, the part is used in the bolt assembly.

Washer (1)

Washer (2)

Washer (3)

Nut (1)

Nut (2)

If the check box is clear, only a hole is created

The chart and the detailed steps below explain the process of bolt length calculation.

  1. Tekla Structures calculates the minimum possible length of the bolt as follows:

    washer (1) thickness (if the check box is selected) +

    material thickness +

    washer (2) thickness (if the check box is selected) +

    washer (3) thickness (if the check box is selected) +

    nut (1) thickness +

    nut (2) thickness +

    extra length

  2. Tekla Structures searches for the closest match in the bolt catalog.

  3. Tekla Structures calculates the number of washers required (must not exceed 10) so that the length of the shaft is less than :

    nut (1) thickness +

    material thickness +

    nut (2) thickness +

    washer (1) thickness +

    washer (2) thickness +

    (number of washers*washer (3) thickness)

  4. Tekla Structures checks that the bolt found in step 2 is longer than :

    extra length +

    nut (1) thickness +

    material thickness +

    nut (2) thickness +

    add. dist (from the bolt catalog) +

    washer (1) thickness +

    washer (2) thickness +

    (number of fitting washers * washer (3) thickness)

  5. If the selected bolt does not fulfill the criteria in step 4, Tekla Structures returns to step 2, otherwise it continues on to step 6.

  6. Tekla Structures checks that the selected bolt fulfills all the following conditions :

    • Can the thread be inside the material to be connected? Even if this is not allowed, the calculation always allows 3 or 4 mm of thread to be inside the material, depending on the bolt diameter. If the bolt diameter is ≥ 24 mm, it allows 4 mm, otherwise it allows 3 mm.

    • Shaft length must be more than:

      material thickness +

      extra length +

      washer (1) thickness (if checked) -

      maximum thread in material allowed (if thread in material = no) = 3 mm or 4 mm

    • Shaft length is calculated as:

      Screw length - screw thread length - thread end.

    • Thread end is the part of the bolt between the shaft and the thread. It is calculated as follows:

      Diameter of bolt (mm)

      Thread end (mm)

      >33.0

      10.0

      >27.0

      8.0

      >22.0

      7.0

      >16.0

      6.0

      >12.0

      5.0

      >7.0

      4.0

      >4.0

      2.5

      ≤4

      1.5

  7. If the selected bolt does not fulfill all the above conditions, Tekla Structures returns to step 2 and tries the next longest bolt.

  8. If the advanced option XS_BOLT_LENGTH_EPSILON is set, the epsilon thickness is added to, or subtracted from, the material thickness to avoid inaccurate bolt length calculation.

    For example, if this value is not taken into account, and the calculated length is 38.001 mm, a 39 mm bolt might be selected.

Quick feedback

The feedback you give here is not visible to other users. We use your comments to improve our content.
We use this to prevent automated spam submissions.
Betyg på innehållet: 
Average page rating: 5 (1 vote)
Refresh page after voting to show updated result.