Release Notes - Tekla Structures 2019i SP2

Defect number Development area Description
TSAC-3475 Concrete components

Meshreinforcement that represents a mesh of steel bars in two perpendicular directions

In Tekla Structures, the reinforcement mesh bars in one direction are called main bars and reinforcement mesh bars perpendicular to them are called crossing bars.

bars
/ Mesh bars by area: On the Detailing tab, the Create cuts around selected parts featurepart of Tekla Structures functionality that is maintained and owned by Trimble Solutions and that is included in the Tekla Structures installation

has been improved. Filter recognition in the list of filters has been improved and the selected filter is now visible when you reopen the component dialog box in the model.

TSAC-3362 Concrete components

Wallplate that represents a structure such as a wall or roof panel

In Tekla Structures, a panel is created by picking two or more points.

In cast-in-place concrete the term wall refers to a concept similar to panel.

layout elementation
has been fixed. You can now use the current units (lbs or kg) as the By weight value in the same way as it has been possible for the maximum weight.

TSAC-3272 Concrete components

Concrete console (110): Previously, the option to cut extra secondary parts was applied to incorrect parts. This has now been fixed.

TSAC-3180 Concrete components

Rectangular column reinforcement (83) now creates intermediate bars between side bars when you have defined an equal number of symmetrical side bars, regardless of the symmetry option you have selected.

TSAC-3132 Concrete components

Wallplate that represents a structure such as a wall or roof panel

In Tekla Structures, a panel is created by picking two or more points.

In cast-in-place concrete the term wall refers to a concept similar to panel.

layout
dialog box has been fixed. Now it works more logically when modifying only the available properties of H, Z1, and Z0 (height, top and bottom level) on the General tab.

TSAC-2963 Concrete components

Reinforcement meshreinforcement that represents a mesh of steel bars in two perpendicular directions

In Tekla Structures, the reinforcement mesh bars in one direction are called main bars and reinforcement mesh bars perpendicular to them are called crossing bars.

array in area (89)
now creates the reinforcement meshreinforcement that represents a mesh of steel bars in two perpendicular directions

In Tekla Structures, the reinforcement mesh bars in one direction are called main bars and reinforcement mesh bars perpendicular to them are called crossing bars.

correctly for the defined polygonal area. Previously, the mesh was not created in some corners of the area and in some cases the mesh extended outside the area.

TSAC-2908 Concrete components

Corbelconcrete part representing a structure that projects from the face of a concrete part and that serves as a support for an overhanging part and connects the parts

Reinforcement (81)
: The main bars now follow the corbel shape properly.

TSAC-2862 Concrete components

Beam reinforcement (63), Strip footingfooting that supports several points of contact or a region of points of contact

Strip footing supports a length of wall or a line of closely spaced columns, for example.

In Tekla Structures, strip footing has a polygon shape that the user defines by picking points.

reinforcement (75)
, Corbelconcrete part representing a structure that projects from the face of a concrete part and that serves as a support for an overhanging part and connects the parts

reinforcement (81)
and Rectangular column reinforcement (83) now have a new U-shape stirrup available.

TSAC-2734 Concrete components

The Update rebar attributes tool now has a new Update (phase only) button with which you can update just the phase of all rebar coupler/end anchor parts.
The existing Update button still functions as before. You can use the Update button to update the coupler/end anchor-specific UDAobject property created by the user in order to widen the range of predefined object properties

User-defined attributes are used when the predefined object properties are not sufficient but more properties are needed. For example, comment, locked, and erection status are user-defined attributes.

values in addition to the phase of coupler/end anchor parts.

TSAC-2720 Concrete components

Automated reinforcement layout - double tee beam (51): You can now use the Ignore cutouts in strandreinforcement that represents a group of wires spun together

layout
 setting on the Attributes tab to ignore cutouts when counting the strand layout.

TSAC-2702 Concrete components

Strip footingfooting that supports several points of contact or a region of points of contact

Strip footing supports a length of wall or a line of closely spaced columns, for example.

In Tekla Structures, strip footing has a polygon shape that the user defines by picking points.

reinforcement (75)
: You can now create straight stirrup rebars.

TSAC-818 Concrete components

Meshreinforcement that represents a mesh of steel bars in two perpendicular directions

In Tekla Structures, the reinforcement mesh bars in one direction are called main bars and reinforcement mesh bars perpendicular to them are called crossing bars.

bars
: You can now set the bar edge distance as a negative value. Note that this will only offset the bars. To get a fully offset mesh, set the cover thickness for the sides on the Bar end conditions tab to a negative value.

TSAC-3411 Steel components

Circular base platecomponent object that represents a plate welded to a column base

Base plates are used to distribute the concentrated load of the column over a wider area.

(1052)
: You can now define the finish property for all parts. On the Anchor rods tab, you can now set the position of the groutbuilding object that represents the filling of seams between parts, or holes or voids in a part with grout

Grouting can be used when connecting parts with anchor bolts or rods, or in seams between panels, for example.

Grout is flowing concrete that hardens after application.

to above or below.

TSAC-3368 Steel components

Splice type 1 (56): The Round web plate(1) part that represents a flat structure

(1) In some contexts, for example in analysis, the term plate object may be used to refer to plates.

(2) plate that represents a steel structure

(2) Plate is mainly used as a connection piece or as a floor plate.

dimensions
option on the Parameters tab now works correctly.

TSAC-3295 Steel components

Splice connection (77): Weld preparations for web plates are now created correctly and do not cause solid errors anymore.

TSAC-3271 Steel components

Column splice (132): You can now define the number of web bolts when using a division plate(1) part that represents a flat structure

(1) In some contexts, for example in analysis, the term plate object may be used to refer to plates.

(2) plate that represents a steel structure

(2) Plate is mainly used as a connection piece or as a floor plate.

and angle profiles as the connection.

TSAC-3054 Steel components

Column with stiffeners (188): Shear tabs are now correctly placed when the main part(1) part that exists in a building object and that determines the position number for the assembly or cast unit and the direction of assembly or cast unit drawings

(1) Main part can be an assembly main part or a cast unit main part.

(2) input part that the user selects first when creating a component

(2) Connections and details always have a component main part.

is created from plates.

TSAC-2807 Steel components

Bolted gussetcomponent object that represents a plate that connects braces to a beam, column, or base plate

(11)
now works in the same way in different Tekla Structures versions.

TSAC-2824 Task Manager

In Task managertool that enables the linking of temporal data to a model

The task manager can be used to create, save, and manage tasks that are used to create a schedule.

Model objects can be added to the tasks. Organizer categories can be used to select the model objects that will be added to the tasks.

, you can now select from 13 predefined custom formats how the dates and the time of tasks are shown.
Click    > Date and time format, and select a suitable format.

TTSD-31129 Import, export, interoperability

IFC2x3 export: The property set mapping double accuracy type is now working correctly, and the size of the export file is reduced.

TTSD-30755 Import, export, interoperability

3D DWG and 3D DGN v8 export: Export failed when there was a space in the layer name. This has now been fixed.

TTSD-30650 Import, export, interoperability

Sometimes the reference modelmodel which the designer can use as an aid when building another model

A reference model is created in Tekla Structures or in other software and can be inserted to Tekla Structures. The reference model appears together with the model but it is not modified by Tekla Structures. The user can snap to reference model points.

For example, an architectural model, a plant design model, or a heating, ventilating, and air-conditioning (HVAC) model can be a reference model.

visibility eye icon state was wrong when you opened the reference model, and you needed to click the icon twice to get the reference model visible. This has now been fixed.

TTSD-29904 Import, export, interoperability

DWG drawing export: Drawing DWG export now handles better situations where views are copied from another drawing with layouts.

TTSD-29494 Import, export, interoperability

IFC2x3 export: The export now uses assembly name for steel parts as well.

TTSD-29283 Import, export, interoperability

IFCfile format commonly used in BIM that facilitates software interoperability

IFC is an open specification developed by the IAI (International Alliance for Interoperability).

Model can be exported into an IFC file.

export
: Holes for bolts going through both faces of hollow section now exported to IFC more consistently, affecting also STEP and IGES exports done with Multi Converter extension.

TTSD-28894 Import, export, interoperability

IFCfile format commonly used in BIM that facilitates software interoperability

IFC is an open specification developed by the IAI (International Alliance for Interoperability).

Model can be exported into an IFC file.

export
: The export had sometimes wrong colors for some objects when exporting bigger amount of objects. This has now been fixed.

TTSD-27862 Import, export, interoperability

IFC4 export: Spatial hierarchy from Organizertool that is used for categorizing and managing model information, object properties and object property queries, and model object classification

Organizer consists of two tools, object browser and categories.

now supports pour units. Note that Organizer Uncategorized are not exported.

TTSD-27780 Import, export, interoperability

IFC4 export: Now when you select the option Pours, pour objects and pour units are exported but cast-in-place concretecast unit type where the concrete is formed, poured, and cured in its final position

parts and cast-in-place cast units are not exported. If you do not select this option, cast-in-place concrete parts and cast-in-place cast units are exported without pour objects or pour units.

TTSD-17311 Import, export, interoperability

IFC2x3 export: The export type Coordination view 2.0 did not always create correct geometry for contour plates with corner chamfers. This has now been fixed.

TTSD-14327 Import, export, interoperability

IFCfile format commonly used in BIM that facilitates software interoperability

IFC is an open specification developed by the IAI (International Alliance for Interoperability).

Model can be exported into an IFC file.

object conversion
: Sometimes the whole model was converted as Item. This has now been fixed.

TTSD-30862 Drawings

Sometimes precast parts with more than 500 edge lines were incorrectly shown in drawing views. This has now been fixed,

TTSD-30731 Drawings

Dragging tables in Layout editortool that enables editing the table layout directly on a drawing

In the layout editor, it is possible select which tables are included in the table layout and where they are placed. The table scale, and rotation and overlapping with drawing views can be adjusted.

has been improved:
- Dragging tables is now smoother.
- You can now drag several tables at one go.
- When you drag tables, snapping is now more reliable.
- When you drag tables, the tables now snap to offsets of 1 mm in metric environments, and 1/16" in the US imperial environment.
- Previously, dragging was not possible in some cases. This has now been fixed.

TTSD-30510 Drawings

Perpendicular leader lineline that connects an annotation object to the related object or point

lengths are now shown in correct scale for views that have a scale value below 1.

TTSD-30329 Drawings

Document managertool that is used for listing and managing drawings and other types of documents

With the document manager the user can, for example, reorganize, update, freeze, lock, and delete drawings.

The user can also organize file documents, such as PDF, NC, and DWG files, and drawings, in document categories, and search documents and open drawings.

Document manager is replacing drawing list from the version 2018i onwards.

could crash if a large number was entered into the search. This has now been fixed.

TTSD-30191 Drawings

Moving copied, linked or multi-drawing container views in drawings was not working. This has now been fixed.

TTSD-29764 Drawings

Inquiring a rebar set from within a drawing did not highlight the corresponding bars in the model. This has now been fixed.

TTSD-29396 Drawings

The TOP_LEVEL_BASEPOINT value was not displayed in drawing views when the value was zero. This has now been fixed.

TTSD-28039 Drawings

The CURRENT_DRAWING.TITLE property now correctly returns a value when used with Select from drawing in drawing viewview that includes selected model objects or an area in the model, that is represented in a drawing

A drawing view is a container for model and drawing objects.

A drawing can include several drawing views, which usually are two-dimensional views, plane views, to the model.

Examples of drawing views in Tekla Structures include main views, section views, single-part views, and 3D views.

properties.

TTSD-26957 Drawings

Previously the NUMBER_IN_DRAWING attribute was not working correctly with tapered rebar sets. This has now been fixed.

TTSD-19675 Drawings

In imported .rtf files the table formatting has been significantly improved.

TTSD-18347 Drawings

Weld marks in drawings that had the size hidden in the weld markmark that includes a set of selected property elements related to a weld

properties were not drawn correctly. This has now been fixed.

TSAC-3456 Drawings

In Tekla Structures 2019i SP1 in 2D library, texts, symbols, and rectangular polygons in 2D details were misplaced. These misplacements were visible when advanced option XS_​UPSIDE_​DOWN_​TEXT_​ALLOWED was set to TRUE.

TTSD-30323 Tekla Model Sharing

In Tekla Model Sharingcloud service for collaboration and for storing and sharing a model

Tekla Model Sharing is one of the Tekla Online services.

, object locks have now been reinforced, so that users in different organizations can no longer accidentally unlock each others' objects or modify the privileges.inp file.

TTSD-30021 Tekla Model Sharing

Tekla Model Sharingcloud service for collaboration and for storing and sharing a model

Tekla Model Sharing is one of the Tekla Online services.

: In the Users dialog box, check marks are now shown again for users that have joined the shared modelmodel used for collaboration over the Tekla Model Sharing service

With a shared model, each user works with their own model and the changes are shared through Tekla Model Sharing. A shared model requires the use of a single-user model. The same model cannot be a shared model and a multi-user model.

.

TTSD-30092 Reinforcement

In rebar sets, the default hook direction now depends only on the first leg. Previously, it was determined from the first two legs including a possible cranked leg at the other end of the bar.

TSAC-3345 Reinforcement

In Rebar shape managertool that is used for customizing the bending shapes of reinforcing bars

Rebar shape manager can be used for bending shapes only and not for any other reinforcing bar properties.

, some extra leg/bending rule operands were previously occasionally shown with short curved bars. These obsolete operands are not shown anymore.

TSAC-3344 Reinforcement

In Rebar shape managertool that is used for customizing the bending shapes of reinforcing bars

Rebar shape manager can be used for bending shapes only and not for any other reinforcing bar properties.

, the rule operand REVERSED was not previously available for curved/circular bars, and therefore it could not be used in shape definitions. This has now been fixed.

TTSD-30193, TTSD-30430, TTSD-30389 Modeling

Previously, creating views along the gridmodeling aid that represents a three-dimensional complex of intersecting grid planes or intersecting grid planes and curved grid surfaces

The grid is defined by coordinates in 3D space. It is shown two-dimensionally on the view plane by dash-and-dot lines. A grid can be rectangular or radial.

It is possible to have more than one grid in a model. For example, a large-scale grid for the entire structure, and smaller grids for some detailed sections.

It is also possible to show grids and grid line labels in drawings, and to modify how they are shown in the drawings.

lines did not work correctly when the grid had a non-zero origin. This has now been fixed.

TTSD-28510, TTSD-29504, TTSD-30166 Modeling

Earlier, when creating a view along the gridmodeling aid that represents a three-dimensional complex of intersecting grid planes or intersecting grid planes and curved grid surfaces

The grid is defined by coordinates in 3D space. It is shown two-dimensionally on the view plane by dash-and-dot lines. A grid can be rectangular or radial.

It is possible to have more than one grid in a model. For example, a large-scale grid for the entire structure, and smaller grids for some detailed sections.

It is also possible to show grids and grid line labels in drawings, and to modify how they are shown in the drawings.

lines for rotated views, incorrect views were created. This has now been fixed.

TTSD-28422, TTSD-25154 Modeling

You can again create construction circles by center point and point on circle. Now when starting the construction circleconstruction object that represents a circle

command, you have 3 options to choose from:

  • Create construction circle by center point and point on circle in view planeplane in a space that defines the view

    In Tekla Structures, the grids are projected onto the view plane and the grid lines can be visible on it.

    View depth is defined starting from the view plane.

    (default)
  • Create construction circle by center point, point on circle and point to pick plane (in 3D)
  • Create construction circle by 3 circle points (in 3D)
TTSD-30851 Modeling

Earlier, sometimes when there were welds in the same position, clash check did not detect clashes. This now has been fixed.

TTSD-30606 Modeling

Previously, if you made large selections in the model, loading properties to the property panecontrol element in Tekla Structures user interface in the form of a side pane window

The property pane can be used to show and modify the properties of model objects.

The property pane can be customized by using the property pane editor.

could be extremely slow. Now this does not happen anymore. The performance issue with large selections has been fixed.

TTSD-30150 Modeling

Welds in components are now taken into account in clash checking.

TTSD-30122 Modeling

Views along gridmodeling aid that represents a three-dimensional complex of intersecting grid planes or intersecting grid planes and curved grid surfaces

The grid is defined by coordinates in 3D space. It is shown two-dimensionally on the view plane by dash-and-dot lines. A grid can be rectangular or radial.

It is possible to have more than one grid in a model. For example, a large-scale grid for the entire structure, and smaller grids for some detailed sections.

It is also possible to show grids and grid line labels in drawings, and to modify how they are shown in the drawings.

lines were not created properly if the work planeplane that the user has chosen in a model and that is currently active for working on in a model view

Newly created, copied, or moved model objects comply with the work plane. For example, shifting the work plane to follow a sloped plane makes it easier to model sloped structures.

was set to some other plane, for instance, when the work plane was rotated. This has now been fixed.

TTSD-29911 Modeling

While editing the geometry of an item and selecting another item, the handles stayed on the original item. This has now been fixed.

TTSD-29098 Modeling

When using a main part(1) part that exists in a building object and that determines the position number for the assembly or cast unit and the direction of assembly or cast unit drawings

(1) Main part can be an assembly main part or a cast unit main part.

(2) input part that the user selects first when creating a component

(2) Connections and details always have a component main part.

UDAobject property created by the user in order to widen the range of predefined object properties

User-defined attributes are used when the predefined object properties are not sufficient but more properties are needed. For example, comment, locked, and erection status are user-defined attributes.

value in the assembly or cast unit position, Tekla Structures erroneously showed the default value of the UDA. This has now been fixed.

TTSD-28366 Modeling

Selecting points that are already selected is now possible after changing the object creation type, for example, creating a polycurve and switching the creation method from arc to line.

TTSD-28182 Modeling

Previously, in some rare cases, numberingprocess of assigning position numbers to parts, cast units, assemblies, or reinforcement

In Tekla Structures, the position numbers assigned in the numbering are shown in marks and templates, for example.

could cause a Tekla Structures model to crash. This could happen at least in the Australasian environment. Now this has been fixed.

TTSD-27826 Modeling

In some cases, for example, when the plane of a part face or an opening face ran through an opening in the part and its pour breakbuilding object used to split a pour object into smaller pour objects

plane, the pour break was not created or it became invalid. This has now been fixed.

TTSD-26805 Modeling

In some cases, weld preparations were not shown in the model after copying. This has now been fixed.

TTSD-30763 Analysis and design

Previously, moving an analysis nodeanalysis model object that Tekla Structures creates at a defined point of an analysis model based on analysis part connectivity

Tekla Structures creates nodes at ends and intersection points of analysis parts, and the corners of analysis areas.

did not create the correct result when multiple parts were connected to the nodeanalysis model object that Tekla Structures creates at a defined point of an analysis model based on analysis part connectivity

Tekla Structures creates nodes at ends and intersection points of analysis parts, and the corners of analysis areas.

. This has now been fixed.

TTSD-28207 Tools and components

Previously, there was an error when publishing a custom componentcomponent that the user creates and uses for creating model objects whose composition the user can modify as a group

in the Applications & components cataloguser interface for displaying or modifying information in categorized lists

For example, profile catalog and shape catalog are catalogs.

when another component of a different type with the same name as the custom component already existed. This has now been fixed.

TTSD-27819 Tools and components

Previously, rebar set modifiers and splitters were hidden in the custom component editortool that is used for modifying component that is created by a custom component, and for creating dependencies between component objects and other model objects

if the XS_REBARSET_SHOW_MODIFIERS_CREATED_BY_COMPONENTS advanced option was set to FALSE. This advanced option should only apply to component instances, not to the component editor. This has now been fixed.

TTSD-29794 User interface

Model viewview that is represented in the modeling mode

Model view is available also in the drawing mode and it is represented in its own window.

visualization with DirectX renderingprocess of making the model object faces visible

The rendered model object faces can be transparent or non-transparent

has been improved for reinforcing bars, handles, and stick representationthe way that the information included in a model is represented visually

:

  • Curved rebars are not anymore shown with a stick line in certain zoom levels.
  • Highlighting for thin rods now always appears.
  • In rebar set: selecting a modifierline or polyline that can be used to locally modify reinforcing bars in a rebar set

    Rebar set modifiers can be rebar set property modifiers, end detail modifiers, or splitters. Also rebar set secondary guidelines behave like rebar set modifiers.

    Polyline modifiers may have corner chamfers. Each rebar set modifier only affects those rebar set reinforcing bars that its projection touches.

    does not change the visibility of the unaffected bars.
  • Rebars do not disappear when zoomed to closely from the top/front angle.
  • Snap symbols are the same size in DirectX rendering than in OpenGL.
  • Changing the rendering mode now works after redraw.
  • Parts change color after redraw.
  • Visualization of parts is not affected by redraw in the Ctrl+1 mode.
  • DirectX rebar representation is now correct after rebar creation.
TTSD-28885 User interface

Previously, the work planeplane that the user has chosen in a model and that is currently active for working on in a model view

Newly created, copied, or moved model objects comply with the work plane. For example, shifting the work plane to follow a sloped plane makes it easier to model sloped structures.

was set to the model originglobal coordinate system point of origin used for the model

Model origin is the default project base point.

when creating default views. This has been fixed and the work plane now remains in the previously set location.

TTSD-25122 User interface

Side pane windows now stay docked or floated when restarting Tekla Structures.
In addition, clicking on a side pane window header will no longer immediately float the window. You need to slightly drag to detach it.

TTSD-24055 User interface

Side pane windows no longer move slightly to the left when floated.

TTSD-15532 User interface

The availability of material, thickness and color properties according to the surface treatmentbuilding object that represents finishing of a part

The term surface treatment is used in concrete detailing. For concrete parts surface treatment includes surface mixes, tiles, and flat finishes, such as troweling and sandblasting.

The term surface finish is used in steel detailing. For steel parts surface finishes include fire-proofing and unpainted areas.

types in the property panecontrol element in Tekla Structures user interface in the form of a side pane window

The property pane can be used to show and modify the properties of model objects.

The property pane can be customized by using the property pane editor.

has been corrected.

TSAC-3525 Import, export, interoperability (concrete)

Export EliPLAN file (68): Recesses that cut the complete area of the element are now plotted.

TSAC-3518 Import, export, interoperability (concrete)

Export Unitechnik (79): When the BRGIRDER block is exported within the STEELMAT block, the STEELMAT insertion coordinates are now correctly adjusted in case the girder minimum coordinate points are outside the meshreinforcement that represents a mesh of steel bars in two perpendicular directions

In Tekla Structures, the reinforcement mesh bars in one direction are called main bars and reinforcement mesh bars perpendicular to them are called crossing bars.

.

TSAC-3488 Import, export, interoperability (concrete)

Export  Unitechnik (79): Braced girders modeled with only two chords are now correctly recognized and exported.

TSAC-3484 Import, export, interoperability (concrete)

Export Unitechnik (79): Previously, braced girders within the STEELMAT block were not exported when the STEELMAT block was otherwise empty. This has now been fixed.

TSAC-3447 Import, export, interoperability (concrete)

Export EliPlan file (68): All geometrical data with the Plotter and Pieces blocks are now exported rounded to the closest millimeter in metric environments.

TSAC-3420 Import, export, interoperability (concrete)

Export EliPlan file (68): Plotter data for cuts and recesses exported as lines will have the thickness/depth value, in case the cut is of even depth.

TSAC-3418 Import, export, interoperability (concrete)

Export EliPlan file (68): Hollow core slabplate that represents a concrete structure

In Tekla Structures, a slab is created by picking three or more points.

Slab may be part of a floor, for example.

thickness is now read from the profile instead of the geometrical thickness (in case the complete top or bottom face is cut).

TSAC-3171 Import, export, interoperability (concrete)

Export Unitechnik (79): On the TS configuration tab you can now set Export CONTOUR to Simplified, which exports a simplified contour using 4 x,y corner points of the element.

TSAC-3165 Import, export, interoperability (concrete)

Export Unitechnik (79): The cutpart former embedbuilding object that represents an object that is to be cast into a concrete structure and that is used to connect structures or as an aid when constructing a structure

For example, a cast-in socket is an embed that is placed in concrete structures to allow parts to be fastened together on site. In Tekla Structures, embeds are typically steel parts and they are added to cast units as sub-assemblies.

polygon is now exported fitted to be within the contour polygon.

TSAC-2470 Import, export, interoperability (concrete)

Export Unitechnik (79): Previously, when a double wallplate that represents a structure such as a wall or roof panel

In Tekla Structures, a panel is created by picking two or more points.

In cast-in-place concrete the term wall refers to a concept similar to panel.

shell was created from more than one part and the Cut outer assemblies option was switched on, the embeds in the secondary part(1) part that exists in a building object and that is connected to the main part

(1) Secondary part can be an assembly secondary part or a cast unit secondary part.

(2) input part that the user selects after selecting the component main part when creating a component

(2) A component can have none, one or more component secondary parts.

were missing from the export with certain Export Groups settings. This has now been fixed.

TSAC-1225 Import, export, interoperability (concrete)

HMS Export: Added new functionality to include slabplate that represents a concrete structure

In Tekla Structures, a slab is created by picking three or more points.

Slab may be part of a floor, for example.

cross bar reinforcement in the export.

TSAC-1224 Import, export, interoperability (concrete)

HMS Export: Rebar strands are now exported from strandreinforcement that represents a group of wires spun together

objects only.