Hello!

Did you know that logged in users can see a lot more content?

Release Notes - Tekla Structures 2019 SP3

Defect number Development area Description
TSAC-3041 Concrete components

In Meshreinforcement that represents a mesh of steel bars in two perpendicular directions

In Tekla Structures, the reinforcement mesh bars in one direction are called main bars and reinforcement mesh bars perpendicular to them are called crossing bars.

bars
, extra secondary bars are no longer created in centrally placed bar groups.

TSAC-3031 Concrete components

In Wallplate that represents a structure such as a wall or roof panel

In Tekla Structures, a panel is created by picking two or more points.

In cast-in-place concrete the term wall refers to a concept similar to panel.

layout
, UDAobject property created by the user in order to widen the range of predefined object properties

User-defined attributes are used when the predefined object properties are not sufficient but more properties are needed. For example, comment, locked, and erection status are user-defined attributes.

values are now set for the surface treatmentbuilding object that represents finishing of a part

The term surface treatment is used in concrete detailing. For concrete parts surface treatment includes surface mixes, tiles, and flat finishes, such as troweling and sandblasting.

The term surface finish is used in steel detailing. For steel parts surface finishes include fire-proofing and unpainted areas.

when it is the first layer.

TSAC-3030 Concrete components

Previously, in Wallplate that represents a structure such as a wall or roof panel

In Tekla Structures, a panel is created by picking two or more points.

In cast-in-place concrete the term wall refers to a concept similar to panel.

layout connector
, the layer-specific attributes (framing case and offsets) in the Wall layout connector dialog box and the actual connection in the model did not match. This issue appeared when the connected primary wall layout had any surfaces other than the last layer.

TSAC-3023 Concrete components

In Reinforced concrete(1) cast unit type where the concrete is formed, poured, and cured in its final position

(2) concrete structure which contains reinforcement designed on the assumption that the concrete and reinforcement act together in resisting forces

(2) Reinforcement in reinforced concrete is usually steel bars, wires, or welded wire fabric. It may also be structural fiber of some other material.

(2) In Tekla Structures, reinforced concrete is modeled with reinforcement objects.

stair (95)
, the STAIR_WIDTH_TOTAL user-defined attributeobject property created by the user in order to widen the range of predefined object properties

User-defined attributes are used when the predefined object properties are not sufficient but more properties are needed. For example, comment, locked, and erection status are user-defined attributes.

is now calculated properly.

TSAC-3000 Concrete components

In Sandwich and double wallplate that represents a structure such as a wall or roof panel

In Tekla Structures, a panel is created by picking two or more points.

In cast-in-place concrete the term wall refers to a concept similar to panel.

, all foils and insulations that are split are now added to the cast unit as defined on the Parts tab.

TSAC-2962 Concrete components

In Corbels and recesses (82), the recognition of cuts has now been improved.

TSAC-2875 Concrete components

Wallplate that represents a structure such as a wall or roof panel

In Tekla Structures, a panel is created by picking two or more points.

In cast-in-place concrete the term wall refers to a concept similar to panel.

layout elementation
has several improvements:

  • Weight in imperial settings now reads lbs correctly.
  • Max weight now has a default of 10000kg when you do not enter any value.
  • When there are no precast parts in the wall layout, the following error message is now shown: "Selected wall layout does not have any precast layers and therefore elementation is not possible."
TSAC-2850 Concrete components

In Floor layout, you can now use Chinese characters in layer names.

TSAC-2501 Concrete components

In Electric box in wallplate that represents a structure such as a wall or roof panel

In Tekla Structures, a panel is created by picking two or more points.

In cast-in-place concrete the term wall refers to a concept similar to panel.

(84)
, distance parameters now work properly with imperial units.

TSAC-2465 Concrete components

Reinforcement meshreinforcement that represents a mesh of steel bars in two perpendicular directions

In Tekla Structures, the reinforcement mesh bars in one direction are called main bars and reinforcement mesh bars perpendicular to them are called crossing bars.

array (91)
now reinforces the entire slabplate that represents a concrete structure

In Tekla Structures, a slab is created by picking three or more points.

Slab may be part of a floor, for example.

area properly.

TSAC-2335 Concrete components

In Tekla Structures 2019 SP2, the direct modificationfunction that activates the mode where the model objects can be modified by using handles

Direct modification enables additional handles and modification options.

arrows for system components and extensions, such as Meshreinforcement that represents a mesh of steel bars in two perpendicular directions

In Tekla Structures, the reinforcement mesh bars in one direction are called main bars and reinforcement mesh bars perpendicular to them are called crossing bars.

bars
, Floor layout tool, and Formwork placing tool, were broken. This has now been fixed.

TSAC-2253 Concrete components

Wallplate that represents a structure such as a wall or roof panel

In Tekla Structures, a panel is created by picking two or more points.

In cast-in-place concrete the term wall refers to a concept similar to panel.

layout
: You can now use the Copy special - Mirror and Move special - Mirror commands to mirror wall layouts.

TSAC-2019 Concrete components

Wallplate that represents a structure such as a wall or roof panel

In Tekla Structures, a panel is created by picking two or more points.

In cast-in-place concrete the term wall refers to a concept similar to panel.

layout opening
: When copying an opening with direct modificationfunction that activates the mode where the model objects can be modified by using handles

Direct modification enables additional handles and modification options.

using the Ctrl button, fillers are now correctly copied along with the opening.

TSAC-1859 Concrete components

Previously, Wallplate that represents a structure such as a wall or roof panel

In Tekla Structures, a panel is created by picking two or more points.

In cast-in-place concrete the term wall refers to a concept similar to panel.

layout
tools used the circular opening settings for rectangular openings if a circular opening was modified before creating the rectangular opening. This has now been changed.

TSAC-3160 Steel components

In Wraparound gussetcomponent object that represents a plate that connects braces to a beam, column, or base plate

cross (60)
, the bolts were rotated incorrectly when the connection was used for twin profiles. This has now been fixed.

TSAC-3140 Steel components

In Gusseted cross (62), the bolt cut lengthbolt property that indicates the depth at which Tekla Structures searches for the sections of the bolted parts

Cut length determines whether the bolt will go through one flange or two, for example.

was too small for thick gussetcomponent object that represents a plate that connects braces to a beam, column, or base plate

plates. This has now been fixed.

TSAC-3129 Steel components

In Wraparound gussetcomponent object that represents a plate that connects braces to a beam, column, or base plate

(58)
, Hollow brace wraparound gusset (59) and Wraparound gusset cross (60), there was issue when the connection plate(1) part that represents a flat structure

(1) In some contexts, for example in analysis, the term plate object may be used to refer to plates.

(2) plate that represents a steel structure

(2) Plate is mainly used as a connection piece or as a floor plate.

had been created as a through-plate. This has now been fixed.

TSAC-3038 Steel components

In Stiffened end platecomponent object that represents a plate welded perpendicular to the end of the component secondary part

(27)
and Partial stiffened end plate(1) part that represents a flat structure

(1) In some contexts, for example in analysis, the term plate object may be used to refer to plates.

(2) plate that represents a steel structure

(2) Plate is mainly used as a connection piece or as a floor plate.

(65)
, the fittingadjustment of a part end

of the secondary part(1) part that exists in a building object and that is connected to the main part

(1) Secondary part can be an assembly secondary part or a cast unit secondary part.

(2) input part that the user selects after selecting the component main part when creating a component

(2) A component can have none, one or more component secondary parts.

was previously incorrectly created in some cases. This has now been fixed.

TSAC-2991 Steel components

In L splice (175) there was an incorrectly created chamfer on the L profile, which was causing problems with numberingprocess of assigning position numbers to parts, cast units, assemblies, or reinforcement

In Tekla Structures, the position numbers assigned in the numbering are shown in marks and templates, for example.

. This has now been fixed.

TSAC-2933 Steel components

In Welded column with stiffeners (128), top and bottom stiffenercomponent object that represents a structure that strengthens a steel beam or column

Stiffeners are usually plates.

Stiffeners are used to prevent web buckling at supports or concentrated loads.

welds were previously swapped. This has now been fixed.

TSAC-2795 Steel components

In Ladder (S35), in some geometrical conditions the hoops were previously created with solid errors. This has now been fixed.

TSAC-2727 Steel components

The countersunk bolts that have been added by using the Metsec components now use a single washer. All other bolts continue to use two washers.

TSAC-2543 Steel components

In Shear plate(1) part that represents a flat structure

(1) In some contexts, for example in analysis, the term plate object may be used to refer to plates.

(2) plate that represents a steel structure

(2) Plate is mainly used as a connection piece or as a floor plate.

simple (146)
, clipping the secondary part(1) part that exists in a building object and that is connected to the main part

(1) Secondary part can be an assembly secondary part or a cast unit secondary part.

(2) input part that the user selects after selecting the component main part when creating a component

(2) A component can have none, one or more component secondary parts.

flange previously depended on the length of the secondary part. This has now been fixed.

TSAC-2359 Steel components

In U.S. Base platecomponent object that represents a plate welded to a column base

Base plates are used to distribute the concentrated load of the column over a wider area.

(1047)
, in some situations, two anchors were previously added to the same assembly. This has now been fixed.

TSAC-2177 Steel components

In H/V Shear plate(1) part that represents a flat structure

(1) In some contexts, for example in analysis, the term plate object may be used to refer to plates.

(2) plate that represents a steel structure

(2) Plate is mainly used as a connection piece or as a floor plate.

(64)
, previously there was the gapany space between two objects

The term gap is used in its general sense in Tekla Structures.

or clash between the shear plate and the main part(1) part that exists in a building object and that determines the position number for the assembly or cast unit and the direction of assembly or cast unit drawings

(1) Main part can be an assembly main part or a cast unit main part.

(2) input part that the user selects first when creating a component

(2) Connections and details always have a component main part.

. This has now been fixed.

TSAC-846 Steel components

In Rebar holesmall hollow open throughout a part or assembly that is usually used for fastening parts with bolts or other such objects

Hole is created in the same way as bolts and hole properties are defined in the bolt properties.

, holes are now created correctly for inclined reinforcing bars with part cuts in steel columns, beams, and contour plates.

TTSD-27752 Organizer

Organizertool that is used for categorizing and managing model information, object properties and object property queries, and model object classification

Organizer consists of two tools, object browser and categories.

performance has now been improved in situations where you open an old model in an environment where a substantial number of property definitions has been changed.

TTSD-27599 Organizer

Synchronization has been improved in Organizertool that is used for categorizing and managing model information, object properties and object property queries, and model object classification

Organizer consists of two tools, object browser and categories.

. Synchronizing Organizer with models that have assemblies containing a lot of subassemblies/parts is much faster than before.

TTSD-25840 Organizer

When you export data to Excel and select the Export without column headers option, the Count column header is not added to the export anymore.

TTSD-20302 Organizer

In Organizertool that is used for categorizing and managing model information, object properties and object property queries, and model object classification

Organizer consists of two tools, object browser and categories.

, when you used the W_Project_data property templatedefinition of object property layout for the property table in object browser

The property template is saved in an .xml file or in the Organizer database.

, the property values of one assembly row in Object Browsertool in Organizer used to inquire, view, and report model information based on selected model objects

were emptied when you exported the object propertiesproperties associated with an object type

Usually a single object property includes a default value that the user can modify.

to Excel. This has now been fixed.

TTSD-28680 Import, export, interoperability

DWG drawing export: Previously, the Export drawings to DWG/DXF dialog box would not open if the advanced option XS_DRAWING_PLOT_FILE_DIRECTORY had no value. This has now been fixed.

TTSD-28021 Import, export, interoperability

IFC4 export: A non-segmented profile is now used for polygon plates.

TTSD-26897 Import, export, interoperability

The bending radii of rebar hooks are now correctly exported to IFC4. Previously, the main rebar bending radii were applied to all bends including hook bends.

TTSD-15289 Import, export, interoperability

DWG drawing export: 2D DWG export now scales the exported file correctly also when US Imperial units are used in the model.

TTSD-28854 Templates and reports

Modifying a report in Template Editortool in Tekla Structures that is used for creating and modifying templates to be used in drawings and reports

was very slow. This has now been fixed and the performance of Template Editor has been improved.

TTSD-27234 Templates and reports

Template Editortool in Tekla Structures that is used for creating and modifying templates to be used in drawings and reports

: Template Editor now shows installed environments when it is started from Windows start menu.

TTSD-27005 Templates and reports

The pull-outsmall graphic in a reinforcement mark, table, or report template that shows the shape and dimensions of a reinforcing bar

attribute now displays the angle values in graphical fields in drawing templates.

TTSD-15807, TTSD-28271 Drawings

A new representationthe way that the information included in a model is represented visually

option outline (ignore holes) has been added for meshes on the Meshreinforcement that represents a mesh of steel bars in two perpendicular directions

In Tekla Structures, the reinforcement mesh bars in one direction are called main bars and reinforcement mesh bars perpendicular to them are called crossing bars.

content
tab in Reinforcement properties.
Additionally, the missing representation option single line with filled ends was added on the Mesh content tab.

TTSD-28212 Drawings

Slotted holesmall hollow open throughout a part or assembly that is usually used for fastening parts with bolts or other such objects

Hole is created in the same way as bolts and hole properties are defined in the bolt properties.

symbols are now drawn correctly again.

TTSD-27840 Drawings

The section marks are no longer referring to wrong views.

TTSD-27776 Drawings

Reference models: Assembly, cast unit, and single-part drawings: Previously, section symbols were created very far apart and view boundaries were too large if the model contained reference models, even when the reference models were not visible in the drawings. This has now been fixed.

TTSD-27485 Drawings

Level marks in drawings were sometimes giving wrong value. This has now been fixed.

TTSD-26791 Drawings

Change clouds are no longer shortened when views are shortened.

TTSD-26142 Drawings

Pull-outsmall graphic in a reinforcement mark, table, or report template that shows the shape and dimensions of a reinforcing bar

pictures in drawing templates now have correct leg lengths for rebar set tapered groups.

TTSD-25974 Drawings

Hatch patterns containing a large number of lines where not correctly displayed in the printing or snapshot output. This has now been fixed.

TTSD-24976 Drawings

Single-part views included in assembly drawings now have correct orientation.

TTSD-24553 Drawings

The Zoom to selected command in drawings was not working correctly in some cases. This has now been fixed.

TTSD-21243 Drawings

Document managertool that is used for listing and managing drawings and other types of documents

With the document manager the user can, for example, reorganize, update, freeze, lock, and delete drawings.

The user can also organize file documents, such as PDF, NC, and DWG files, and drawings, in document categories, and search documents and open drawings.

Document manager is replacing drawing list from the version 2018i onward.

search box now supports macrosaved series of actions that includes instructions for a program

Macros are located in the applications and components catalog. They are recorded or created manually and stored as .cs file in a folder defined with the advanced option XS_MACRO_DIRECTORY.

Macros can, for example, be used for creating drawings or reports.

Macros are sometimes used to run an application.

recording and playback.

TTSD-21114 Drawings

The List hidden objects in templates option in drawings now works more reliably.

TTSD-20488 Drawings

Previously, dragging drawing text from the ruler instead of the ruler handle could cause Tekla Structures to crash. This has now been fixed.

TTSD-19787 Drawings

You can now print to more than one printer in one go. To do so, select the Use multiple printers option in the Print Drawings dialog box.

TTSD-17795 Drawings

The drawing section marks no longer refer to wrong views.

TTSD-17143 Drawings

A new button Show all documents has been added to Document managertool that is used for listing and managing drawings and other types of documents

With the document manager the user can, for example, reorganize, update, freeze, lock, and delete drawings.

The user can also organize file documents, such as PDF, NC, and DWG files, and drawings, in document categories, and search documents and open drawings.

Document manager is replacing drawing list from the version 2018i onward.

. This button resets the document list so that all documents are visible, and all searches and filtering is cleared. Excluded categories remain excluded. This new featurepart of Tekla Structures functionality that is maintained and owned by Trimble Solutions and that is included in the Tekla Structures installation

also provides a convenient way to restore the document list to a default state when recording macros.

TSAC-3003 Drawings

Rebar groupgroup of reinforcing bars that are side by side and have identical properties, except the possible variation in bar lengths

dimensioning:
 the dimension markpart of a dimension that displays the basic information about the building object measurements

A dimension mark can consist of a prefix, numerical value, and postfix.

and line to rebar are now correctly placed in a customized position.

TSAC-2869 Drawings

Rebar groupgroup of reinforcing bars that are side by side and have identical properties, except the possible variation in bar lengths

dimensioning:
 Rebar groups are now dimensioned in polybeams.

TTSD-27827 Tekla Model Sharing

The following fixes have been made in Tekla Model Sharingcloud service for collaboration and for storing and sharing a model

Tekla Model Sharing is one of the Tekla online services.

:
- The green arrow on the Read in button is now shown correctly if there are no packets available to read in.
- Previously, if model changes were written out too many times within a short time frame, Tekla Structures sometimes lost track of the changes and could not show the number of packets that users could read in. This has now been fixed.

TTSD-26837 Tekla Model Sharing

Reference models: Previously in shared models, conflicts with reference models at read-in sometimes caused situations where reference objects could not be shown as invisible in the model viewview that is represented in the modeling mode

Model view is available also in the drawing mode and it is represented in its own window.

. This has now been fixed.

TTSD-16162 Tekla Model Sharing

The appearance of usernames in the history of shared models has been unified. The usernames are now shown in the domain\name format.

TTSD-15628 Tekla Model Sharing

Previously, when a multi-user modelmodel that is used for collaboration and that is opened in multi-user mode

was converted into a shared modelmodel used for collaboration over the Tekla Model Sharing service

With a shared model, each user works with their own model and the changes are shared through Tekla Model Sharing. A shared model requires the use of a single-user model. The same model cannot be a shared model and a multi-user model.

, inserting an object could appear twice in the object history. This has now been fixed.

TTSD-14480 Tekla Model Sharing

Previously in Tekla Model Sharingcloud service for collaboration and for storing and sharing a model

Tekla Model Sharing is one of the Tekla online services.

, saving a copy of a shared modelmodel used for collaboration over the Tekla Model Sharing service

With a shared model, each user works with their own model and the changes are shared through Tekla Model Sharing. A shared model requires the use of a single-user model. The same model cannot be a shared model and a multi-user model.

with the Save As option could erase the creation time and creator of model objects. This has now been fixed so that the creation time of model objects is the time that the copied model was saved, and the creator is the user that saved the model.

TTSD-27964 Reinforcement

Previously, Tekla Structures crashed when you copied rebar set properties and other objects were selected along with the target rebar set. This has now been fixed.

TTSD-26803 Reinforcement

In rebar sets, when you were placing a splitterrebar set modifier that can be used to split the reinforcing bars in a rebar set and to create reinforcement splices

modifierline or polyline that can be used to locally modify reinforcing bars in a rebar set

Rebar set modifiers can be rebar set property modifiers, end detail modifiers, or splitters. Also rebar set secondary guidelines behave like rebar set modifiers.

Polyline modifier may have corner chamfers. Each rebar set modifier only affects those rebar set reinforcing bars that its projection touches.

and tried to snap to mid points, snapping did not work correctly. This has now been fixed.

TSAC-2747 Reinforcement

In Rebar shape managertool that is used for customizing the bending shapes of reinforcing bars

Rebar shape manager can be used for bending shapes only and not for any other reinforcing bar properties.

, the value of total length along center line (CLL) was not correct in case the bending radius values and angles were varying. This has now been fixed.

This fix also affects reports if the CLL value has been used for calculations.

TTSD-28122 Modeling

Previously, a warning message was shown when you opened the user-defined attributes (UDAs) dialog box for a cast unit sub-assemblyassembly in a nested assembly that is subordinate to a parent assembly

from the property panecontrol element in Tekla Structures user interface in the form of a side pane window

The property pane can be used to show and modify the properties of model objects.

. This has now been fixed.

TTSD-27870 Modeling

Snapping to the nearest point now works when using the Ortho tool.

TTSD-27762 Modeling

Previously, if a bent plate(1) part that is created from contour plates, or beams whose profile is a plate

(1) Bent plates can be conical or cylindrical.

Curved beams, spiral beams, or deformed parts cannot be used for creating a bent plate.

(2) component object that represents an angle that is bent from a plate and that connects parts

had several edge chamfers, removing one of them caused others to disappear. This has now been fixed.

TTSD-27743 Modeling

Previously, saving a multi-user modelmodel that is used for collaboration and that is opened in multi-user mode

with the Save as command could cause problems when trying to open or save the model later. This has now been fixed.

TTSD-27623 Modeling

Previously, changing the visibility of reference models caused conflicts in multi-user models. This has now been fixed.

TTSD-27157 Modeling

Previously, when you modified gridmodeling aid that represents a three-dimensional complex of horizontal and vertical planes

In Tekla Structures, grids are used as an aid in locating objects in a model. The grid is shown on the view plane by dash-and-dot lines. It is also possible to show grids and grid line labels in drawings, and to modify grid properties in the drawings.

It is possible to have more than one grid in a model. For example, a large-scale grid for the entire structure, and smaller grids for some detailed sections.

properties in the property panecontrol element in Tekla Structures user interface in the form of a side pane window

The property pane can be used to show and modify the properties of model objects.

using US imperial units, the distances with feet and inches that included feet symbols and the inches having fractional values (a'-b.c") did not work correctly. This has now been fixed.

TTSD-26815 Modeling

The Work planeplane that the user has chosen in a model and that is currently active for working on in a model view

Newly created, copied, or moved model objects comply with the work plane. For example, shifting the work plane to follow a sloped plane makes it easier to model sloped structures.

handler
toolbar now works better when saving multi-user models (save and model reopen). The toolbar now keeps the set work plane when saving the model.

TTSD-25515 Modeling

When using the Ortho tool, the snap symbol is now again shown as the snap to any position symbol.

TTSD-24605 Modeling

The Model search toolbar now searches also for pour objects by pour typeproperty of a pour object that uses a cast-in-place part name or a manually given value to describe the pour object

By default the part name is used for pour type. The part name used is the name of the part with the largest volume in the pour object.

and pour units by name, if the pour management is enabled.

TSD-27117 Modeling

Previously, when you welded a non-solid item, Tekla Structures would crash. This has now been fixed.

TTSD-26713 Core

Trimble Connectorfeature that enables interoperability between Tekla Structures and Trimble Connect application

has been updated to a new version, with updated identity handling.

TTSD-26089 Core

There has been a security update to the CefSharp library, an embedded web browser in the Online side pane, due to the CVE-2019-5786 vulnerability. The CefSharp library has been updated to version 71.0.2.

TSAC-3261 Tools and components

Previously, Layout Managertool that is used to import and export layout data between Tekla Structures and field layout devices

Layout manager enables the use of accurate model point and line data on the construction site.

could crash if you modified the properties of a base pointpoint in a model that is used to define a starting point in surveying and that is used as an anchor point in coordinate and height transformations

A Tekla Structures project can have several base points but only one of them can be the project base point.

Base points allow the use of another coordinate system needed for interoperability and collaboration. Base points can also be used in drawings, and in reports and templates. Model origin is the default base point in Tekla Structures.

Base points are also called control points.

that was assigned to groups in Layout Manager. This has now been fixed.

TSAC-2978 Tools and components

Layout managertool that is used to import and export layout data between Tekla Structures and field layout devices

Layout manager enables the use of accurate model point and line data on the construction site.

now displays a dialog box that shows the progress of some commands.

TTSD-27961 User interface

Selecting the profile and the material from the profile and material catalogs in the property panecontrol element in Tekla Structures user interface in the form of a side pane window

The property pane can be used to show and modify the properties of model objects.

now works correctly when creating parts.

TTSD-27392 User interface

In the Object groupmodel objects with settings that match the settings that the user has defined for a certain purpose

In Tekla Structures, an object group is used on the one hand to control the transparency and coloring of model objects in the views and on the other in project management. Object groups can also be used in filtering tools, for example in selection filter, to select all objects that match certain properties.

- View filterfilter used for defining which objects are displayed in a model view or drawing view

View filter chooses objects according to object properties. The user can filter objects according to their profile or material, for example.

dialog box, having spaces before or after the text in the Value field no longer causes the text to disappear.

TTSD-22777 User interface

Previously, when you maximized the Customize toolbars dialog box, the OK, Apply, Discard and Cancel buttons at the bottom of the dialog box were not visible. This has now been fixed.

TTSD-20908 User interface

The construction lineconstruction object that represents a line between two points

extension in the contextual toolbarfloating toolbar that contains commands for modifying the most common object properties

The user can customize the contextual toolbar.

The term mini toolbar is used in Tekla Structures until version 21.1.

now follows the unit settings.

TTSD-18005 User interface

You can now change the space between cut parts on the contextual toolbarfloating toolbar that contains commands for modifying the most common object properties

The user can customize the contextual toolbar.

The term mini toolbar is used in Tekla Structures until version 21.1.

in the drawing modemode that is used for editing the appearance and content of drawings

Tekla Structures switches to the drawing mode when the user opens any drawing.

.

TSAC-3217 Import, export, interoperability (concrete)

Export Unitechnik (79): In some cases, rebars exported as mountparts were plotted with double lines. This has now been fixed.

TSAC-3172 Import, export, interoperability (concrete)

Export Unitechnik (79): A Profile centerline to pallet centerline option has been added for the Align in Y axis setting on the Pallet tab. With the Profile centerline to pallet centerline option, you can automatically align hollow-core slabs to the center of the pallet in Y direction. 

TSAC-3158 Import, export, interoperability (concrete)

Export Unitechnik (79): The SLABDATE rotation angle only setting has been renamed to With SLABDATE rotation angle, as it now rotates the element and also exports the rotation angle.

TSAC-3029 Import, export, interoperability (concrete)

Export Unitechnik (79): When using file name block options it is now possible to specify input text without delimiters.

TSAC-2888 Import, export, interoperability (concrete)

BVBS Export: The Advanced tab now contains new options for rounding rebar lengths for 2D bent bars. Mesh and 3D rebars are not affected.
To round the lengths, first select an option for the Round setting. The options are:
Yes - UseS the nearest rounding value.
Up - Rounds the lengths up.
Down - Rounds the lengths down.
The new option Round lengths to rounds the total rebar lengths in the corresponding BVBS field in the header block, and the available values are 1, 5, 10, and 25.
The new option Round leg lengths to rounds the leg lengths in the geometry block, and the available values are 1, 5, and 10.
1 is the default value for both options.

TSAC-2540 Import, export, interoperability (concrete)

EliPlan Export (68): Plotter data export has been improved.