In Beam reinforcement (63), Bar end cover now works correctly for beams that have an L-profile.

In Meshreinforcement that represents a mesh of steel bars in two perpendicular directions

In Tekla Structures, the reinforcement mesh bars in one direction are called main bars and reinforcement mesh bars perpendicular to them are called crossing bars.

bars by area, bars are again created only to the area defined by the polygon input.

In Embedded anchors (8), the bending radius of rebar A and rebar B now works correctly.

In Concrete beam-beam (112), the Parameters tab now has an option for perpendicular cuts on the underside of the beam.

In Concrete console (110), when defining on the Picture tab how the shape of the secondary beam is modified, you can now select to cut the column perpendicular to the secondary beam.

Electric box in wallplate that represents a structure such as a wall or roof panel

In Tekla Structures, a panel is created by picking two or more points.

In cast-in-place concrete the term wall refers to a concept similar to panel.

(84) now applies direction and rotation of custom componentcomponent that the user creates and uses for creating model objects whose composition the user can modify as a group

parts correctly. Previously, the custom component for the bottom connection was not correctly created, and when a custom component was created at a bend, then both (top and bottom) connections were created incorrectly.

In Create holesmall hollow open throughout a part or assembly that is usually used for fastening parts with bolts or other such objects

Hole is created in the same way as bolts and hole properties are defined in the bolt properties.

around part (92), it is now possible to create exact holes around circular sections.

In Base platecomponent object that represents a plate welded to a column base

Base plates are used to distribute the concentrated load of the column over a wider area.

(1004), the plate(1) part that represents a flat structure

(1) In some contexts, for example in analysis, the term plate object may be used to refer to plates.

(2) plate that represents a steel structure

(2) Plate is mainly used as a connection piece or as a floor plate.

, leveling plate and shimcomponent object that represents a plate that is used for filling clearances and gaps on the construction site

plates are now positioned correctly as defined. Also, bolts, anchor rods and custom components are now positioned correctly.

In Seating cap (37), it is now possible to define the material and name for Prim end platecomponent object that represents a plate welded perpendicular to the end of the component secondary part

and Washer plates on the Parts tab.

In Base platecomponent object that represents a plate welded to a column base

Base plates are used to distribute the concentrated load of the column over a wider area.

(1004), you can now set the classpart property that groups parts according to identifiers given by the user

The identifiers of classes are usually numbers. Classes can be used for defining the color of parts in the model, for example. Class does not influence the numbering of model objects.

information for each plate(1) part that represents a flat structure

(1) In some contexts, for example in analysis, the term plate object may be used to refer to plates.

(2) plate that represents a steel structure

(2) Plate is mainly used as a connection piece or as a floor plate.

on the Parts tab.

In Spiral stair (S68), the number of turns is now correct with both the clockwise and counter clockwise setting. The positions of inner toe profiles are now also correct with the clockwise setting.

In Two sided clip anglecomponent object that represents a right angle that is made of a standard L-shaped profile and that connects parts

(117), the correct number of bolts is now created.

In Stiffened shear plate(1) part that represents a flat structure

(1) In some contexts, for example in analysis, the term plate object may be used to refer to plates.

(2) plate that represents a steel structure

(2) Plate is mainly used as a connection piece or as a floor plate.

(17), the shear tabcomponent object that represents a plate welded to the component main part and bolted to the web of the component secondary part

is now created correctly, and the shim platecomponent object that represents a plate that is used for filling clearances and gaps on the construction site

is created when defined. The bolt spacing for the secondary part(1) part that exists in a building object and that is connected to the main part

(1) Secondary part can be an assembly secondary part or a cast unit secondary part.

(2) input part that the user selects after selecting the component main part when creating a component

(2) A component can have none, one or more component secondary parts.

now also works correctly.

In Column with stiffeners W (182), weld number 7 is now positioned correctly for the bottom NS stiffenercomponent object that represents a structure that strengthens a steel beam or column

Stiffeners are usually plates.

Stiffeners are used to prevent web buckling at supports or concentrated loads.

.

In Cast-in plate(1) part that represents a flat structure

(1) In some contexts, for example in analysis, the term plate object may be used to refer to plates.

(2) plate that represents a steel structure

(2) Plate is mainly used as a connection piece or as a floor plate.

(1069), the bolts now work correctly with plate washers. Also, it is now possible to set slotted holesmall hollow open throughout a part or assembly that is usually used for fastening parts with bolts or other such objects

Hole is created in the same way as bolts and hole properties are defined in the bolt properties.

options when using plate washers.

In Hollow brace wraparound gussetcomponent object that represents a plate that connects braces to a beam, column, or base plate

(59), the brace connection plate(1) part that represents a flat structure

(1) In some contexts, for example in analysis, the term plate object may be used to refer to plates.

(2) plate that represents a steel structure

(2) Plate is mainly used as a connection piece or as a floor plate.

is now positioned correctly when using a chamfered brace connection plate. The chamfers are now created correctly in the brace connection plate. The boxes for chamfer values are now unavailable when chamfers cannot be created in the brace connection plate.

In Stringer to channel (127), the option to set the angle position on the Parameters tab now works correctly.

In Splice plate(1) part that represents a flat structure

(1) In some contexts, for example in analysis, the term plate object may be used to refer to plates.

(2) plate that represents a steel structure

(2) Plate is mainly used as a connection piece or as a floor plate.

2 (62), the flange bolts are now correctly created when using profiles with a small height.

In Two sided end platecomponent object that represents a plate welded perpendicular to the end of the component secondary part

- Cfl (112), it is now possible to define the material and the name separately for the end plates and the compensating plates.

In Haunchcomponent object that represents a wedge-like structure that strengthens a beam at its end

(40), weld number 6 is now in the correct position when the secondary part(1) part that exists in a building object and that is connected to the main part

(1) Secondary part can be an assembly secondary part or a cast unit secondary part.

(2) input part that the user selects after selecting the component main part when creating a component

(2) A component can have none, one or more component secondary parts.

is skewed, and the haunch is made from a profile.

In Organizertool that is used for categorizing and managing model information, object properties and object property queries, and model object classification

Organizer consists of two tools, object browser and categories.

, when you had a category with a filter that referred to a Project category to use the Project category content, and you changed the object content of the Project category, only the second Organizer synchronization updated the object content of the category using the filter. This has now been fixed.

In Task managertool that enables the linking of temporal data to a model

The task manager can be used to create, save, and manage tasks that are used to create a schedule.

Model objects can be added to the tasks. Organizer categories can be used to select the model objects that will be added to the tasks.

, when you click   to calculate the planned dates for the objects in the taskin the task manager, a representation of a piece of work that needs to be carried out in order to complete a project

, the subtasks of the selected task are also updated.

In Unitechnik export (79), calculation for sloped bars is now correct when main parts have cuts.

Unitechnik export (79) now exports sloped slabs (balcony parts)  in the SLABDATE block.

Sometimes reference models caused a big drawing view framesolid frame around all the contents of a drawing view

Drawing view frame can be used when modifying properties of a single drawing view. Drawing views can be dragged using the drawing view frame.

. This has now been fixed.

Marks containing templates were not working correctly in multidrawings. This has now been fixed.

The Combine command no longer creates arc symbols in polygons.

A part of the weld markmark that includes a set of selected property elements related to a weld

content was duplicated when the mark was on the left side and the advanced option XS_AISC_WELD_MARK was set to TRUE. This has now been fixed.

The minimum allowed size in the Gridmodeling aid that represents a three-dimensional complex of intersecting grid planes or intersecting grid planes and curved grid surfaces

The grid is defined by coordinates in 3D space. It is shown two-dimensionally on the view plane by dash-and-dot lines. A grid can be rectangular or radial.

It is possible to have more than one grid in a model. For example, a large-scale grid for the entire structure, and smaller grids for some detailed sections.

It is also possible to show grids and grid line labels in drawings, and to modify how they are shown in the drawings.

number and Grid text boxes in the Advanced grid labelname of a grid line

properties dialog box is 1.0.

Unfolding bent plate(1) part that is created from contour plates, or beams whose profile is a plate

(1) Bent plates can include conical or cylindrical sections.

(1) Curved beams, spiral beams, or deformed parts cannot be used for creating a bent plate.

(2) component object that represents an angle that is bent from a plate and that connects parts

dimensions for horizontal bends were not created at all, or were created on horizontal dimensions. Now this has been fixed and horizontal bend information is shown in vertical dimensions.

When bent plate(1) part that is created from contour plates, or beams whose profile is a plate

(1) Bent plates can include conical or cylindrical sections.

(1) Curved beams, spiral beams, or deformed parts cannot be used for creating a bent plate.

(2) component object that represents an angle that is bent from a plate and that connects parts

or polybeampart of a certain shape that is created as a continuous chain of beams passing through points that the user picks

The segments of the polybeam are straight, but segment intersections can be curved. For example, a beam that follows a zigzag line is a polybeam.

dimension parameters were changed through the contextual toolbarfloating toolbar that contains commands for modifying the most common object properties

The user can customize the contextual toolbar.

, the bending angle and radius texts disappeared. This has now been fixed.

In Tekla Model Sharingcloud service for collaboration and for storing and sharing a model

Tekla Model Sharing is one of the Tekla Online services.

, read in changes were not shown if there were user-defined attributes with duplicate names in the model. This has now been fixed.

Previously, Tekla Structures stopped working in some cases when importing profiles. This has now been fixed.

Surface treatmentbuilding object that represents finishing of a part

The term surface treatment is used in concrete detailing. For concrete parts surface treatment includes surface mixes, tiles, and flat finishes, such as troweling and sandblasting.

The term surface finish is used in steel detailing. For steel parts surface finishes include fire-proofing and unpainted areas.

color is now correctly shown as selected in the surface treatment properties when changing the surface type.

Autosave now works correctly in the Project viewer configuration.

Keyboard shortcuts that have been duplicated no longer cause a Tekla Structures applicationpart of Tekla Structures functionality that is developed in order to extend the capability of Tekla Structures but that is not included in the Tekla Structures installation

error.

You can create a new model to a network drive again.

In Kingspan Cold rolled sleeved (28) and Kingspan Horizontal Cladding sleeve (120), stay holes and purlins are now created in pairs, and the bolt size on stay cleats attached to rafters and columns is now by default set to 16 mm.

Kingspan Cold rolled sleeved (28) now works with variable depth rails that have a common sheeting line. Multicleat holes can also be added for visualization purposes.

In Kingspan Cold rolled sleeved (28), stay holes in rails and purlins are now inserted in pairs.

There are now new options in Kingspan non-standand tie (6):

• Orientation: Default or reversed. Reversed defines the tie in the other direction.
• General bolt grade: Controls the bolt grade at both ends of the tubular, unless the counterformed option is selected in the Start/End condition option. If Counterformed is selected, the Standard Counterformedscrew standard will be used for the start bolt.

Extensions (.tsep) are now installed when you restart Tekla Structures. Previously, some extensions were not installed but instead these extensions remained in the installation queue and the installer tried to install them each time you restarted Tekla Structures.

Sometimes, the numberingprocess of assigning position numbers to parts, cast units, assemblies, or reinforcement

In Tekla Structures, the position numbers assigned in the numbering are shown in marks and templates, for example.

status, whether up-to-date or not, was not correctly preserved when saving a shared modelmodel used for collaboration over the Tekla Model Sharing service

With a shared model, each user works with their own model and the changes are shared through Tekla Model Sharing. A shared model requires the use of a single-user model. The same model cannot be a shared model and a multi-user model.

with Save as. This has now been fixed.