Array tools now have a new parameter to skip copying the UDAs if not needed.

Objects with polygon cuts can now be copied again using Radial array tool.

When handles are visible, you can now snap to them, even when they are within an opaque object.

In a shared modelmodel used for collaboration over the Tekla Model Sharing service

With a shared model, each user works with their own model and the changes are shared through Tekla Model Sharing. A shared model requires the use of a single-user model. The same model cannot be a shared model and a multi-user model.

, the drawing status is now correctly updated in a user's local model when reading in.

The Logical weld property now works in reports. Previously, the result in a report was always empty. 

Deleting objects copied using Linear array tool now also deletes the cuts and fittings that were in the copied objects.

Copying and modifying the number of objects copied with an array tool by using another array tool does not make Tekla Structures to crash anymore.

Earlier, grids exported from Tekla Structural Designer did not always appear in correct elevations when imported to Tekla Structures. This has now been fixed.

In Joist to Beam and Col. (164), you can now again define the angle position numberidentifier that is assigned to all similar parts, assemblies, cast units, or reinforcement

Position number consists of a prefix, separator, and running number. The prefix is part of the position number, identifying a numbering series. The running number is part of the position number, and is the assigned number in the numbering series, based on the start number. The separator is an optional character, such as a slash, that separates the prefix and the running number.

In Tekla Structures, the position numbers assigned in the numbering are shown in marks and templates, for example.

In the US, the term piece mark or ship mark is used to refer to a position number.

, material and name on the Stabilizer tab.

In bent plate(1) part that is created from contour plates, or beams whose profile is a plate

(1) Bent plates can be conical or cylindrical.

Curved beams, spiral beams, or deformed parts cannot be used for creating a bent plate.

(2) component object that represents an angle that is bent from a plate and that connects parts

unfolding drawings, when a bending line is skewed, both ends of the bending line are dimensioned on both X and Y axis, in order to get all the needed dimensions.

Previously, saving a large model got very slow if the model had been created with Save as and it was again saved with Save as. This has now been fixed.

Earlier, when the model contained grids in negative elevations in Tekla Structural Designer, the grids did not appear at all after export and import into Tekla Structures. This has now been fixed.

When using Radial array tool to copy objects, the polygon cuts, line cuts and fittings now work correctly when the copied object clashes with the original objects or neighboring parts.

Inch mark is now supported correctly in the custom component editortool that is used for modifying component that is created by a custom component, and for creating dependencies between component objects and other model objects

. Previously, when adding labels, for example, an inch mark 36'-0", an error would occur when the .inp file was loaded the next time.

Hovering the mouse pointer over model objects now makes the object color darker so that the original object color can still be seen. Previously, hovering changed the object color to gray, which hid the original object color.

In Rebar holesmall hollow open throughout a part or assembly that is usually used for fastening parts with bolts or other such objects

Hole is created in the same way as bolts and hole properties are defined in the bolt properties.

, you can now use imperial values for Hole diameter. The Hole type option now works correctly when set to Part cutcut that is defined by a cutting part

or Bolt hole + Part cut.

Previously clicking Modify in the drawing viewview that includes selected model objects or an area in the model, that is represented in a drawing

A drawing view is a container for model and drawing objects.

A drawing can include several drawing views, which usually are two-dimensional views, plane views, to the model.

Examples of drawing views in Tekla Structures include main views, section views, single-part views, and 3D views.

properties dialog box without selecting anything from the options tree, or selecting mark options tree without changing the existing applied settings sometimes caused marks to change position. This has now been fixed.

A new version of the Support tool is now introduced for reporting issues with Tekla Structures. The new Support tool uses Trimble Identityuser account to Tekla online services and other Trimble services

For a Tekla Structures user, Trimble Identity is a single sign-on account which enables the user’s online identity management. The organization that the user’s Trimble Identity belongs to, determines the user’s access rights. Trimble Identity is needed, for example, for Tekla Campus and Tekla Warehouse, and to log in to Tekla User Assistance.

for log in. You can start the tool from the File menu by clicking Help > Contact Tekla support, or by entering Contact Tekla support in Quick Launchtool that is used for quickly finding commands, dialog boxes, and other functions in Tekla Structures

The other functions include local content from Tekla Warehouse, for example.

.