Hello!

Did you know that logged in users can see a lot more content?

Extensions

Metsec Non-Standard Horizontal Cladding Support (34)

The Metsec Non-Standard Horizontal Cladding Support macrosaved series of actions that includes instructions for a programMacros are located in the applications and components catalog.
by Trimble Solutions UK
0

Metsec Non-Continuous Rail (106)

The Metsec Non-Continuous Rail system joint is normally used when the specified column face to cladding distance is less than that possible for the standard purlin/rail joint. The joint can handle flush or recessed sheeting lines. A non-standard cleat, (either angle or tee), is welded to the column, and bolted to the rail using holes along the standard gauge lines.
by Trimble Solutions UK
0

Metsec Gable Post Shear Plate (105)

The Metsec Gable Post Shear Plate(1) part that represents a flat structure(1) In some contexts, for example in analysis, the term plate object may be used to refer to plates.(2) plate that represents a steel structure(2) Plate is mainly used as a connection piece or as a floor plate. is provided as a connection between a C-section or compound C-section column and a gable rafter. However, it may be applied to similar situations.
by Trimble Solutions UK
0

Metsec Apex Ties (30)

The Metsec Apex Ties macrosaved series of actions that includes instructions for a programMacros are located in the applications and components catalog. They are recorded or created manually and stored as .cs file in a folder defined with the advanced option XS_MACRO_DIRECTORY.Macros can, for example, be used for creating drawings or reports.Macros are sometimes used to run an application. can be used to define various types of ties between the two purlins of an apex.
by Trimble Solutions UK
0

Metsec Base Plate (1006)

The Metsec Base Platecomponent object that represents a plate welded to a column baseBase plates are used to distribute the concentrated load of the column over a wider area. detail will add cleats to the bottom end of a column to provide a base for the connection of the column. When used with Metsec sections the detail will use appropriate trimmer cleats by default. You will be required to pick a primary member followed by a point.
by Trimble Solutions UK
0

Metsec Cold Rolled Sleeved (102)

The Metsec Cold Rolled Sleeved connection is used to connect one or two purlins/rails to a rafter/stanchion. It can be used for sleeved joints, butt joints, in the middle of double span purlins/rails, and at gable ends. It should not be used for connections to hip rafters for which a separate joint is available. For simplicity, this help text, and the joint dialogue, will refer only to purlins and rafters, but unless explicitly stated otherwise, these terms should be taken to mean purlins/rails and rafters/stanchions.
by Trimble Solutions UK
0

Metsec cold rolled - Important information

When utilising the Metsec cold rolled system it is important to take the following information into account.
by Trimble Solutions UK
0

Metsec Cold Rolled Cleat (101)

The Metsec Cold Rolled Cleat joint uses manufacturers trimmer cleats or mezzanine floor cleats to provide connections between various combinations of compatible ‘I’, ‘Z’ and ‘C’ sections.
by Trimble Solutions UK
0

Metsec Diagonal Ties (27)

The Metsec Diagonal Ties macrosaved series of actions that includes instructions for a programMacros are located in the applications and components catalog.
by Trimble Solutions UK
0

Metsec Eaves Brace (24)

The Metsec Eaves Brace macrosaved series of actions that includes instructions for a programMacros are located in the applications and components catalog.
by Trimble Solutions UK
0

Metsec File Transfer (26)

The Metsec File Transfer macrosaved series of actions that includes instructions for a programMacros are located in the applications and components catalog. They are recorded or created manually and stored as .cs file in a folder defined with the advanced option XS_MACRO_DIRECTORY.Macros can, for example, be used for creating drawings or reports.Macros are sometimes used to run an application. will create a transfer file compatible with the Metsec detailing program.
by Trimble Solutions UK
0

Metsec Eaves Beam to Stanchion (104)

The Metsec Eaves Beam to Stanchion macrosaved series of actions that includes instructions for a programMacros are located in the applications and components catalog.
by Trimble Solutions UK
0

Smart3D Interoperability

Contents Purpose and descriptionSystem requirementsInstallationApplications and Components menuVersion historyUsageExport to Intergraph Smart™ 3DCreating or editing a subset
by Steel Extensions
0

Metsec Apex Ties (30)

The Metsec Apex Ties macrosaved series of actions that includes instructions for a programMacros are located in the applications and components catalog. They are recorded or created manually and stored as .cs file in a folder defined with the advanced option XS_MACRO_DIRECTORY.Macros can, for example, be used for creating drawings or reports.Macros are sometimes used to run an application. can be used to define various types of ties between the two purlins of an apex.
by Trimble Solutions UK
0

Metsec Base Plate (1006)

The Metsec Base Platecomponent object that represents a plate welded to a column baseBase plates are used to distribute the concentrated load of the column over a wider area. detail will add cleats to the bottom end of a column to provide a base for the connection of the column. When used with Metsec sections the detail will use appropriate trimmer cleats by default. You will be required to pick a primary member followed by a point.
by Trimble Solutions UK
0

Metsec cold rolled - Important information

When utilising the Metsec cold rolled system it is important to take the following information into account.
by Trimble Solutions UK
0

Metsec Cold Rolled Cleat (101)

The Metsec Cold Rolled Cleat joint uses manufacturers trimmer cleats or mezzanine floor cleats to provide connections between various combinations of compatible ‘I’, ‘Z’ and ‘C’ sections.
by Trimble Solutions UK
0

Metsec Cold Rolled Sleeved (102)

The Metsec Cold Rolled Sleeved connection is used to connect one or two purlins/rails to a rafter/stanchion. It can be used for sleeved joints, butt joints, in the middle of double span purlins/rails, and at gable ends. It should not be used for connections to hip rafters for which a separate joint is available. For simplicity, this help text, and the joint dialogue, will refer only to purlins and rafters, but unless explicitly stated otherwise, these terms should be taken to mean purlins/rails and rafters/stanchions.
by Trimble Solutions UK
0

Metsec Diagonal Ties (27)

The Metsec Diagonal Ties macrosaved series of actions that includes instructions for a programMacros are located in the applications and components catalog.
by Trimble Solutions UK
0

Metsec Eaves Beam to Stanchion (104)

The Metsec Eaves Beam to Stanchion macrosaved series of actions that includes instructions for a programMacros are located in the applications and components catalog.
by Trimble Solutions UK
0

Pages

.