Extensions
Kingspan Simple Hip (14)
The Simple Hip Connection is provided to form a connection between a single cold-rolled purlin and a hip or valley rafter
Selection Process:
Rafter/Hot-Rolled member
Kingspan cold-rolled
September 16, 2016
by Trimble Solutions UK
Kingspan Autoform One Sided (20)
This connection Autoform one Sided (20) is used to connect a Multichannel (Compound or Single) to a main member
Selection Process:
Select Primary cold-rolled member
Select Secondary cold-rolled member
Limitations:
September 16, 2016
by Trimble Solutions UK
Kingspan Shearplate to hip (8)
The Kingspan Shearplate to hip connection is used to connect one or two purlins/rails to a rafter/stanchion. It can be used for connections to Hip rafters, in the middle of double span purlins/rails.
Selection Process:
Select Main Member
Select Secondary parts and press middle button
September 16, 2016
by Trimble Solutions UK
Kingspan Cleader Angle (13)
When detailing a Kingspan Cleader Angle (13) macrosaved series of actions that includes instructions for a programMacros are located in the applications and components catalog.
September 16, 2016
by Trimble Solutions UK
Kingspan Gable Post Shear Plate (105)
Selection Process:
Pick main member i.e. Hot-Rolled/Rafter
Mutlichannel/Gable post member
September 16, 2016
by Trimble Solutions UK
Kingspan Apex Tie (9)
The Apex Tie macrosaved series of actions that includes instructions for a programMacros are located in the applications and components catalog.
September 16, 2016
by Trimble Solutions UK
Kingspan Multichannel Base Cleat (4)
This detail will define either AUTOFORMED end(s) for the column with a base platecomponent object that represents a plate welded to a column baseBase plates are used to distribute the concentrated load of the column over a wider area., single/double cold rolled cleats with a base plate(1) part that represents a flat structure(1) In some contexts, for example in analysis, the term plate object may be used to refer to plates.(2) plate that repr
September 16, 2016
by Trimble Solutions UK
Kingspan Panel Joint at Mid-Span (21)
When detailing a Horizontal Cladding System, the Kingspan / Metl-Con Panel Joint at Mid-Span (21) macrosaved series of actions that includes instructions for a programMacros are located in the applications and components catalog.
September 16, 2016
by Trimble Solutions UK
Organizer - Task Manager Link
With the Organizertool that is used for categorizing and managing model information, object properties and object property queries, and model object classificationOrganizer consists of two tools, object browser and categories. - Task Managertool that enables the linking of temporal data to a modelThe task manager can be used to create, save, and manage tasks that are used to create a schedule.Model objects can be added to the tasks.
September 16, 2016
by Tekla Extensions Global
Kingspan Horizontal Cladding sleeve (120)
The Cold Rolled Sleeved connection is used to connect one or two Kingspan channels to a Hot-rolled member. It can be used for sleeved joints; butt joints; in the middle of double span purlins/rails; and at gable ends. It should not be used for connections to Hip rafters for which a separate joint is available.
Selection Process:
September 16, 2016
by Trimble Solutions UK
Curved Rebars for coupler Toolbox
ContentsPurpose and descriptionSystem requirementsInstalling Curved Rebars For Coupler Toolbox
September 12, 2016
by Trimble Solutions France
Cranking of overlapping rebars
Use for:
Visualization of overlapping rebars.
Example:
Example
September 7, 2016
by Precast Extensions
Area Reinforcement
The Area Reinforcement plugincomponent that is developed using Tekla Open APIPlugin is a .dll file and loaded inside Tekla Structures process.Plugins can be started from the applications and components catalog. automatizes the process of reinforcing walls and slabs. Itcreates custom rebar meshes that cover the faces with bigger area of the part.These custom meshes may have different distances between bars and also bars of different sizes.
August 31, 2016
by Precast Extensions
Area Reinforcement: Crossing bars tab
Use the Crossing bars tab to set prefered and minimal spacing between the normal crossing bars and to set the gridmodeling aid that represents a three-dimensional complex of intersecting grid planes or intersecting grid planes and curved grid surfacesThe grid is defined by coordinates in 3D space. It is shown two-dimensionally on the view plane by dash-and-dot lines. A grid can be rectangular or radial.It is possible to have more than one grid in a model.
August 31, 2016
by Precast Extensions
Area Reinforcement: Longitudinal bars tab
Use the Longitudinal bars tab to set prefered and minimal spacing between the normal longitudinal bars and to set the gridmodeling aid that represents a three-dimensional complex of intersecting grid planes or intersecting grid planes and curved grid surfacesThe grid is defined by coordinates in 3D space. It is shown two-dimensionally on the view plane by dash-and-dot lines. A grid can be rectangular or radial.It is possible to have more than one grid in a model.
August 31, 2016
by Precast Extensions
Area Reinforcement: Parameters tab
Use the Parameters tab to set the meshes to create and their parameters like: Size, Grade, Name, Position prefix and Start no and classpart property that groups parts according to identifiers given by the userThe identifiers of classes are usually numbers. Classes can be used for defining the color of parts in the model, for example. Class does not influence the numbering of model objects..
August 31, 2016
by Precast Extensions
Area Reinforcement: Cover thickness tab
Use the Cover thickness tab to set both meshes cover thicknesses from side and from openings.
Properties
August 31, 2016
by Precast Extensions
Area Reinforcement: Additional bars tab
Use the Additional bars tab to define placing and parameters of additional bars.
August 31, 2016
by Precast Extensions
Custom Attributes
Few attributes are available in model but cannot be called in reports. This extension installs a set of new variables & which allows to use them wherever it is required such as in reports, marks as templates, drawings, API, filtering, object representationrepresentation of a model object or an object group in a model view that is based on the color and transparency settings applied to the model object or the object group, etc.
August 31, 2016
by Developer TIN
Pages
.