Hello!

Did you know that logged in users can see a lot more content?

Extensions

Flange Cut

Use Flange Cut to cut a flange of an 'L' Section obstructing by another L section flange.
by Developer TIN
0
  • transmission
  • tower
  • Cut
  • flange
  • flange cut
  • angle cut
  • Angle

Tower Bent Plates

Use Tower Bent Plates tool to connect tower member between two members which are in different plane and or different orientation. Unlike Tekla connections, here the bent plates has to create first (to get the proper plane for the connecting member) and then the connecting Tower Member.
by Developer TIN
0
  • towers
  • tower
  • transmission towers
  • transmission tower
  • bent
  • plate
  • plates
  • bent plates

Cut Open Angle

In Transmission Towers, when an angle ('L') section (primary) leg surface is not parallel to ground level but the angle section (s) which is going to connect (seating) with the primary is parallel to the ground, then 'Cut Open Angle' tool can be  used to cut open or close the primary leg to create a seating surface for the secondary(secondaries).
by Developer TIN
0
  • Cut
  • Cut open
  • transmission
  • towers
  • Cut Operation
  • start
  • end
  • intermediate
  • 1050
  • 1051

Plan Cut

Use Plan Cut when two members ( 'L' sections) flanges are intersecting at 90 degree and if both flanges need to be cut at same time. This happens at the corners of transimission towers transitions.
by Developer TIN
0
  • transmission
  • tower
  • Cut
  • flange
  • flange cut
  • angle cut
  • Angle
  • plan
  • plan cut

Back Cut

Use Back Cut when a member ('L' section) clash with another ('L' section) and  need to trim or extend and maintain bolt edge distance on first member.
by Developer TIN
0
  • transmission
  • tower
  • Cut
  • flange
  • flange cut
  • angle cut
  • Angle
  • back
  • back cut

Object dimensioning

With this tool, you can create dimensioning of erection drawings fast. It adds overall dimensions in both directions, creates an extrema mark and line with object information and adds locations from grids. Installing Object dimensioning tool To install the extension:
by Jiri Martinek
0

Clip Off Cut

Use Clip off Cut to cut an 'L' section flange at an angle by picking a point on the flage which needs to cut. This type of cut used widely in Transmission Tower detailing to remove unwanted flange projection.
by Developer TIN
0
  • transmission
  • tower
  • Cut
  • flange
  • flange cut
  • clip
  • clip off cut
  • angle cut
  • Angle

Gage Line by Point

Use Gage Line by Point  for creating construction lines representing local bolt gages on Angle (L) sections. This make easy for snap points for inserting other  members or bolts on the already inserted member.
by Developer TIN
0
  • gage
  • Line
  • gage line
  • gauge
  • gauge line
  • point
  • gauge line by point
  • by point
  • line by point
  • gage line by point

Gage Line

Use Gage Line for creating construction lines representing bolt gages on Angle (L) sections. This make easy for snap points for inserting other  members or bolts on the already inserted member.
by Developer TIN
0
  • gage
  • Line
  • gage line
  • gauge
  • gauge line
  • point
  • gauge line by point
  • by point
  • line by point
  • gage line by point

Tower Bent Member

Use Tower Bent Member tool to create  bent tower members between two members which are in different plane and or different orientation . 
by Developer TIN
0
  • towers
  • tower
  • Member
  • members
  • transmission
  • transmission tower
  • transmission towers
  • bent member
  • bent members

Grasshopper-Tekla Live Link

Introduction The Grasshopper-Tekla live link enables algorithmic modelling for Tekla Structures using Rhino/Grasshopper. The link is a set of Grasshopper components that can create and interact with objects live in Tekla Structures. Demo Videos Building Frame
by Tekla Extensions - General Design
4.454545

Spiral staircase 2.1

  Contents Purpose and descriptionSystem requirementsInstalling Spiral staircaseUsing Spiral staircaseGeneral tabParts tabStep tabStringer tabUsing direct modification  
by Steel Extensions
0

Tower Member

Use Tower Member tool to create tower members on tower slopes. This tool find out an imaginary plane which leave no or less gapany space between two objectsThe term gap is used in its general sense in Tekla Structures. between the matching leg surfaces on slope and create member.
by Developer TIN
0
  • tower
  • Member
  • transmission
  • towers
  • Tower Member

Tower View Creator

Tower View Creator is an extension which create side views for 'Tower Line Tool'. As the views are created along the slope, it is easy for the user to work on specific side views created on slope if the tower line is tapered.
by Developer TIN
0
  • Tower View
  • tower
  • Sloped
  • tapered
  • tower line
  • Line
  • transmission

Tower Line Tool

Use Tower Line Tool for creating rectangular transmission tower layout using construction lines. This make easy for inserting members in 3D by using snap points.
by Developer TIN
0
  • transmission
  • tower
  • towers
  • tower line
  • Line
  • layout

Doubler Plate

This package installs two plugins one to manage location of doubler platecomponent object that represents a structure that strengthens a steel beam web or steel column web by thickening it created with End platecomponent object that represents a plate welded perpendicular to the end of the component secondary part connection and another will create additional doubler plate(1) part that represents a fl
by Developer TIN
2
  • Doubler Plate

Flange Web Bolt Separator

'CUSTOM.BOLTSEPARATOR' is a bolt custom propertyobject property that the user can manually include in OrganizerSome properties are not automatically available in the Organizer, for example the properties of reference model objects. which can be called in reports to check the bolt is attached to flange or web. One use case for this is to find number of tapered washers to bill out based on count of flange bolts. It checks only three profiles for this. Those are 'I', 'T', 'C' and 'U'.
by Mohammad Faizal
0
  • flange
  • web
  • Bolt
  • report
  • segregation
  • segregate
  • separator
  • separate
  • differentiate
  • CUSTOM.BOLTSEPARATOR

Welded to top flange plate chamfer

This package will install a plugincomponent that is developed using Tekla Open APIPlugin is a .dll file and loaded inside Tekla Structures process.Plugins can be started from the applications and components catalog. 'Welded to top flange extension'.
by Developer TIN
0

Concrete Estimator

1. Purpose and descriptionThis package installs Concrete Estimation tool which generates estimation from the Tekla Structures Model as per Indian Standard (IS1200) Estimation contains Concrete Volume , Formwork Area, (calculations as per IS1200) , Rebar weight and rebar coupler quantity (as avaialble in the model). Phase wise excel report can be extracted for estimation.  2. System requirementsEnvironments: IndiaLanguages: ENGLISH
by Developer TIN
0
  • Concrete Estimator
  • concrete
  • Estimator

Smart3D Interoperability

Contents Purpose and descriptionSystem requirementsInstallationApplications and Components menuVersion historyUsageExport to Intergraph Smart™ 3DCreating or editing a subset
by Steel Extensions
0

Pages

.