Angle Rail Components
2021
Tekla Structures
2020
Tekla Structures
2019i
Tekla Structures
2019
Tekla Structures
2018i
Tekla Structures
2018
Tekla Structures
Environment
United States (Imperial)
United States (Metric)
CATALOG NAME: Angle Rail-Angle Conx; Angle Rail Conx; Angle Rail Cut
Angle Rail-Angle Conx
TYPE: CONNECTION
This Custom Component is used to connection two angle rails (created using S77) at 90° corners with a bolted angle.
There are four location options that this Custom Component uses to locate the angle in relation to the two angle rails which you should set before applying the connection to the parts. However it you don't apply it first, just modify it after is is applied to get the desired angle position.
You also need to set the Rail Rotation option accordingly so it matches the rotation of the rail profiles you are connecting.
Before you start do the following:
Picking order (always from the perspective of the acute angle side)
1. Left side Angle Rail
2. Right side Angle Rail
Option 1 - Inside-Vertical Leg Inside
Option 2 - Outside-Vertical Leg Inside
Option 3 - Outside-Vertical Leg Outside
Option 4 - Inside-Vertical Leg Outside
Angle Rail Conx - Back to top
TYPE: CONNECTION
Use this Custom Component to join two angle rails at a corner.
Picking order:
1. Select the Angle Rail which will be extended
2. Select the other Angle Rail which will be cut and get a plate welded to it.
NOTE: Depending on the orientation of the first angle rail, the plate and cut will not get created correctly for the second rail.
When this occurs, change the Up direction to -z on the General tab.
As a result, the plate and cut will be created correctly.
How the bolt is located.
If you enter 0" for the bolt edge values, then the bolt will be located in the center of the plate.
Otherwise, you can enter a desired edge values and these values will be used to located the bolt.
Angle Rail Cut - Back to top
TYPE: SEAM
This Custom Component is used to cut one leg of a middle Angle rail around an Angle Stanchion.
You can control the cut gap as shown here.
This Custom Component can be used inside System Component S77 on the Middle Rails tab by loading in this Angle Rail Cut custom component and the Industrial_Angle attribute or any other attribute you save inside this custom component.
This component is also included in the ENG_BaseTemplate and ENG_PlateworkModel model templates.
Angle Rail-Angle Conx
TYPE: CONNECTION
This Custom Component is used to connection two angle rails (created using S77) at 90° corners with a bolted angle.
There are four location options that this Custom Component uses to locate the angle in relation to the two angle rails which you should set before applying the connection to the parts. However it you don't apply it first, just modify it after is is applied to get the desired angle position.
Image
You also need to set the Rail Rotation option accordingly so it matches the rotation of the rail profiles you are connecting.
Image
Before you start do the following:
- Create at least 2 angle handrail systems, 90° to each other. It is recommended to use the provided Industrial_Angle attribute in S77 as a start point.
- Make sure the Objects in Components icon is down
Picking order (always from the perspective of the acute angle side)
1. Left side Angle Rail
2. Right side Angle Rail
Option 1 - Inside-Vertical Leg Inside
Image
Option 2 - Outside-Vertical Leg Inside
Image
Option 3 - Outside-Vertical Leg Outside
Image
Option 4 - Inside-Vertical Leg Outside
Image
Angle Rail Conx - Back to top
TYPE: CONNECTION
Use this Custom Component to join two angle rails at a corner.
Image
Picking order:
1. Select the Angle Rail which will be extended
2. Select the other Angle Rail which will be cut and get a plate welded to it.
Image
NOTE: Depending on the orientation of the first angle rail, the plate and cut will not get created correctly for the second rail.
Image
When this occurs, change the Up direction to -z on the General tab.
Image
As a result, the plate and cut will be created correctly.
Image
How the bolt is located.
If you enter 0" for the bolt edge values, then the bolt will be located in the center of the plate.
Image
Image
Otherwise, you can enter a desired edge values and these values will be used to located the bolt.
Image
Image
Angle Rail Cut - Back to top
TYPE: SEAM
This Custom Component is used to cut one leg of a middle Angle rail around an Angle Stanchion.
Image
You can control the cut gap as shown here.
Image
This Custom Component can be used inside System Component S77 on the Middle Rails tab by loading in this Angle Rail Cut custom component and the Industrial_Angle attribute or any other attribute you save inside this custom component.
Image
This component is also included in the ENG_BaseTemplate and ENG_PlateworkModel model templates.
Starting in v21.1, the above Custom Components are available in all US Environment Model Templates
- CIP-Rebar Detailing (hidden)
- Engineering (hidden)
- Precast Detailing (hidden)
- Steel Detailing*