Hello!

Did you know that logged in users can see a lot more content?

Stiffened base plate (1014)

Last updated March 12, 2019 by Tekla User Assistance tekla.documentation@trimble.com

Software version: 
2019

Stiffened base plate (1014)

Stiffened base plate (1014)

Stiffened base plate (1014) creates a base platecomponent object that represents a plate welded to a column base

Base plates are used to distribute the concentrated load of the column over a wider area.

that is connected to a column end.

Objects created

  • Base plate(1) part that represents a flat structure

    (1) In some contexts, for example in analysis, the term plate object may be used to refer to plates.

    (2) plate that represents a steel structure

    (2) Plate is mainly used as a connection piece or as a floor plate.

  • Stiffeners

  • Shimcomponent object that represents a plate that is used for filling clearances and gaps on the construction site

    plates (optional)

  • Leveling plate (optional)

  • Shear keycomponent object that represents a short steel part welded to the bottom of a base plate

    (optional)

  • Extra plates connecting the anchor rods

  • Anchor rods

  • Bolts

  • Welds

  • Additional component (optional)

Use for

Situation

Description

Base plate with stiffeners

Base plate with stiffeners on the flange

Base plate with stiffeners on the flange

Base plate with stiffeners on the flange

Base plate with stiffeners on the flange

Base plate with stiffeners on the web

Before you start

Create a column.

Selection order

  1. Select the main part(1) part that exists in a building object and that determines the position number for the assembly or cast unit and the direction of assembly or cast unit drawings

    (1) Main part can be an assembly main part or a cast unit main part.

    (2) input part that the user selects first when creating a component

    (2) Connections and details always have a component main part.

    (column).

  2. Pick a position.

    The detail is created automatically.

Part identification key

 

Part

1

Base plate

2

Shim plate

3

Leveling plate

4

Shear key

5

Stiffener

Picture tab

Use the Picture tab to control the position of the base plate and the length and position of the shear key.

Dimensions

 

Description

Default

1

Distance from the flange to the edge of the base plate.

Enter a negative value to make the base plate larger.

2

Weld gap.

3

Height of the shear key.

Equal to the column width

Shear key offset

 

Description

1

Distance of the stiffener from the edge of the column flange.

2

Shear key vertical offset from the column center.

3

Shear key horizontal offset from the column center.

Parts tab

Use the Parts tab to control the dimensions of the base plate, web plates, flange plates, shear key, leveling plate, and shim platecomponent object that represents a plate that is used for filling clearances and gaps on the construction site

(s).

Plate

Option

Description

Default

Plate

Base plate thickness.

BASEPLATE

Web plates

Web plate thickness.

10 mm

Flange plate 4

Flange plate thickness.

10 mm

Additional beam

Shear key profile by selecting it from the profile catalog.

HEA 300 (in Default environment)

Leveling plate

Leveling plate thickness, width and height.

Fitting plate

Shim plate thickness, width and height.

Define up to three different shim plates.

Number of fitting pl.

Number of shim plates for each thickness.

1

Horizontal plates

Horizontal plate thickness.

L profile, flange

Profile for L profile, flange by selecting it from the profile catalog.

L profile, web

Profile for L profile, web by selecting it from the profile catalog.

Leveling plate hole diameter

Leveling plate hole diameter.

Option

Description

Default

Pos_No

Prefix and start number for the part position number.

Some components have a second row of fields where you can enter the assembly position number.

The default part start number is defined in the Components settings in File menu > Settings > Options.

Material

Material grade.

The default material is defined in the Part material box in the Components settings in File menu > Settings > Options.

Name

Name that is shown in drawings and reports.

 

Class

Part class number.

 

Finish

Describes how the part surface has been treated.

 

Bolt edge distances in shim plate

Define the bolt edge distances for shim plates. When these fields are empty, shim plates are of the same size as the base plate.

 

Description

Default

1

Horizontal bolt edge distance in the shim plate.

30 mm

2

Vertical bolt edge distance in the shim plate.

30 mm

Shim plate shape

Option

Description

Default

Holes are based on the bolt group of the detail.

AutoDefaults can change this option.

Holes are based on the bolt group of the detail.

Finger shim plate with horizontal slots.

The plate can be installed from the right or left side of the detail.

Finger shim plate with vertical slots.

The plate can be installed from the top of the detail.

Tolerance

Define the tolerance for the slots in finger shimshim plate with slots cut through the edge

plates. The width of the slot is the bolt diameter + the tolerance.

Parameters tab

Use the Parameters tab to control the component and the groutbuilding object that represents the filling of seams between parts, or holes or voids in a part with grout

Grouting can be used when connecting parts with anchor bolts or rods, or in seams between panels, for example.

Grout is flowing concrete that hardens after application.

holesmall hollow open throughout a part or assembly that is usually used for fastening parts with bolts or other such objects

Hole is created in the same way as bolts and hole properties are defined in the bolt properties.

.

Grout hole

Define whether a grout hole is created in the base plate. The hole is also created in the leveling plate and shim plates, if they exist in the detail.

Option

Description

Default

Grout hole is not created.

AutoDefaults can change this option.

Grout hole is not created.

Grout hole is created.

Grout hole dimensions

 

Description

1

Location of the grout hole from the center of the column in the direction of the web.

2

Grout hole diameter.

3

Location of the grout hole from the center of the column in the direction of the flange.

Using additional components

You can use additional system or custom components to modify the column end or the base plate. For example, you can create special backing plates, weld preparations, and weld access holes for the column end.

If you use additional system or custom components, you need to manage the column end or the base plate properties in the additional component in question. When using several components, there may be multiple welds and cuts.

Optioon

Description

Component

Define a system or a custom component by selecting it from the Applications & components catalog.

Attributes

Enter the name of the attribute file for the selected component.

Input

Define to which parts the selected component is applied.

  • Default is same as Base + Column.

  • Column sets the column as the main part. Use this option for details.

  • Column + Base sets the column as the main part and the base plate as the secondary part.

  • Base + Column sets the base plate as the main part and the column as the secondary part.

Bolts

Use the Bolts tab to control the bolt properties.

Bolt group dimensions

 

Description

1

Select how to measure the dimensions for horizontal bolt group position.

  • Left : From the left edge of the secondary part to the leftmost bolt.

  • Middle : From the center line of the secondary part to the center line of the bolts.

  • Right : From the right edge of the secondary part to the rightmost bolt.

2

Dimension for horizontal bolt group position.

3

Bolt edge distance.

Edge distance is the distance from the center of a bolt to the edge of the part.

4

Number of bolts.

5

Bolt spacing.

Use a space to separate bolt spacing values. Enter a value for each space between bolts. For example, if there are 3 bolts, enter 2 values.

6

Dimension for vertical bolt group position.

7

Select how to measure the dimensions for vertical bolt group position.

  • Top : From the upper edge of the secondary part to the uppermost bolt.

  • Middle : From the center line of the bolts to the center line of the secondary part.

  • Below : From the lower edge of the secondary part to the lowest bolt.

8

Define which bolts are deleted from the bolt group.

Enter the bolt numbers of the bolts to be deleted and separate the numbers with a space. Bolt numbers run from left to right and from top to bottom.

Bolt basic properties

Option

Description

Default

Bolt size

Bolt diameter.

Available sizes are defined in the bolt assembly catalog.

Bolt standard

Bolt standard to be used inside the component.

Available standards are defined in the bolt assembly catalog.

Tolerance

Gap between the bolt and the hole.

 

Thread in mat

Defines whether the thread may be within the bolted parts when bolts are used with a shaft.

This has no effect when full-threaded bolts are used.

Yes

Site/Workshop

Location where the bolts should be attached.

Site

Slotted holes

You can define slotted, oversized, or tapped holes.

Option

Description

Default

1

Vertical dimension of slotted hole.

0 , which results in a round hole.

2

Horizontal dimension of slotted hole, or allowance for oversized holes.

0 , which results in a round hole.

Hole type

Slotted creates slotted holes.

Oversized creates oversized or tapped holes.

No hole does not create holes.

 

Rotate Slots

When the hole type is Slotted , this option rotates the slotted holes.

 

Slots in

Part(s) in which slotted holes are created. The options depend on the component in question.

 

Bolt assembly

The selected check boxes define which component objects (bolt, washers, and nuts) are used in the bolt assemblyset of bolt elements that consists of a bolt, a stud, or a screw, and possibly the related washers and nuts

.

If you want to create a hole only, clear all the check boxes.

To modify the bolt assembly in an existing component, select the Effect in modify check box and click Modify.

Bolt length increase

Define how much the bolt length is increased. Use this option when, for example, painting requires the bolt length to be increased.

Stiffeners

Use the Stiffeners tab to control the web plate stiffeners and the flange platecomponent object that represents a plate that connects the flanges of a beam to a column

Flange plates are used in moment connections, for example.

stiffeners.

Web plate stiffener dimensions

 

Description

Default

1

Height of the web plate stiffener.

200 mm

2

Bottom width of the web plate stiffener.

100 mm

Web plate stiffener chamfer dimensions

 

Description

1

Top horizontal chamfer dimension.

2

Top vertical chamfer dimension.

3

Bottom horizontal chamfer dimension.

4

Bottom vertical chamfer dimension.

Web plate stiffener position

You can create stiffeners to different positions using the web plate stiffenercomponent object that represents a structure that strengthens a steel beam or column

Stiffeners are usually plates.

Stiffeners are used to prevent web buckling at supports or concentrated loads.

position options.

Option

Description

Default

Type 2

AutoDefaults can change this option.

Type 1

Type 2

Type 3

Type 4

Type 5

Type 6

Type 7

Flange plate stiffener dimensions

 

Description

Default

1

Height of the flange plate stiffener.

200 mm

2

Bottom width of the flange plate stiffener.

100 mm

Flange plate stiffener chamfer dimensions

 

Description

1

Top horizontal chamfer dimension.

2

The top vertical chamfer dimension.

3

Bottom horizontal chamfer dimension.

4

Bottom vertical chamfer dimension.

Flange plate stiffener position

You can create stiffeners to different positions using the flange plate stiffener position options.

Option

Description

Default

Type 2

AutoDefaults can change this option.

Type 1

Type 2

Type 3

Type 4

Stiffener dimensions

If you have created the stiffeners using other than the default stiffener position options, you can separately define the plate dimensions for different positions.

 

Description

1

Width of the stiffener.

2

Height of the stiffener.

3

Width of the stiffener.

Stiffener plate width

If you have selected type 5 as the web plate stiffener position or type 4 as the flange plate stiffener position, you can define the stiffener width.

 

Description

Default

1

Width of the stiffener.

200 mm

Stiffener chamfer dimensions

 

Description

1

Horizontal chamfer dimension.

2

Vertical chamfer dimension.

Anchor rods tab

Use the Anchor rods tab to control the creation of different types of anchor rods.

Anchor rod dimensions

Option

Description

Anchor rod profile

Anchor rod profile.

Nut profile

Nut profile.

Washer profile

Washer thickness, width and height.

Plate washer

Plate washer thickness, width and height.

Cast plate

Cast plate thickness, width and height.

Anchor rod part properties

Option

Description

Default

Pos_No

Prefix and start number for the part position number.

Some components have a second row of fields where you can enter the assembly position number.

The default part start number is defined in the Components settings in File menu > Settings > Options.

Material

Material grade.

The default material is defined in the Part material box in the Components settings in File menu > Settings > Options.

Name

Name that is shown in drawings and reports.

 

Class

Part class number.

 

Grout thickness

Groutingbuilding object that represents the filling of seams between parts, or holes or voids in a part with grout

Grouting can be used when connecting parts with anchor bolts or rods, or in seams between panels, for example.

Grout is flowing concrete that hardens after application.

helps you to model columns to the top of concrete parts and to place the base plate correctly. It also makes it easier to dimension the detail in general arrangement drawings.

By default, no grouting is created.

Enter the grout thickness. Select whether the grouting is created above or below the detail creation point. This also affects the shim plates.

Base plate with

Use this option to switch between the bolts and the anchor rods.

By default, the base plate is created with Bolts.

Anchor rod dimensions

 

Description

Default

1

Size or the length of the nut.

anchor rod diameter

2

Size or the thickness of the washer.

half of nut size

3

Length of the anchor rod.

500 mm

4

Length of the anchor rod above the base plate.

50 mm

5

Distance between the cast plate and the base plate.

60 mm

6

Length of the upper thread.

0 mm

Anchor rods types

Option

Description

 

Default

Type 1

AutoDefaults can change this option.

 

Type 1

 

a

Radius of the hook

b

Width of the hook

a = 2*anchor bar diameter

b = 1/5 of anchor bar length

a

Radius of the hook

b

Width of the hook

c

Height of the hook

c = same as width of the hook

d

Length of the anchor rod below the extra plate

e

Length of the lower thread

d = 2*nut size

e = 4*nut size plus thickness of extra plate

Hook direction

Option

Description

Default

Type 1

AutoDefaults can change this option.

Type 1

Type 2

Type 3

Type 4

Bolting direction

Note:

You can define the bolting direction if you have created the base plate with bolts.

Option

Description

Default

Bolting direction 1

AutoDefaults can change this option.

Bolting direction 1

Bolting direction 2

Cast plate holes tolerance

Option

Description

Default

Cast plate holes tolerance

Tolerance of the cast plate holes.

same as bolt tolerance

Washer hole tolerance

Option

Description

Create hole in washer

By default, a hole is not created in the washer.

Tolerance of the washer hole.

Create assembly from all anchors

Define whether anchors are included in an anchor rod assembly. You can also include leveling plates into the assembly.

Create

 

Description

1

Create the nut profile.

2

Create the washer profile.

3

Create the washer plate.

Anchor rod assembly

Define which parts of the anchor rod are included in the anchor rod assembly.

Extra plates tab

Use the Extra plates tab to control the placement, rotation, and type of the profiles (extra profile 1) created at the bottom of each anchor bar and the profiles (extra profile 2) that connect rows of anchor bars.

Part dimensions

Option

Description

Default

Extra profile 1

First extra profile by selecting it from the profile catalog.

PL10*100

Extra profile 2

Second extra profile by selecting it from the profile catalog.

Part properties

Option

Description

Default

Pos_No

Prefix and start number for the part position number.

Some components have a second row of fields where you can enter the assembly position number.

The default part start number is defined in the Components settings in File menu > Settings > Options.

Material

Material grade.

The default material is defined in the Part material box in the Components settings in File menu > Settings > Options.

Name

Name that is shown in drawings and reports.

 

Class

Part class number.

 

Edge distance of extra profile 1

 

Description

Default

1

Edge distance of extra profile 1.

50 mm

Type and direction of extra profile 1

Option

Description

Default

Type 1

AutoDefaults can change this option.

Type 1

Type 2

Type 3

Edge distance of extra profile 2

 

Description

Default

1

Distance of extra profile 2 from the axis of the anchor bar.

Half of the nut size or anchor bar diameter

Extra profile 2 type

Option

Description

Default

Type 1

AutoDefaults can change this option.

Type 1

Type 2

Type 3

Type 4

Type 5

Type 6

Length of extra profile 2

 

Description

Default

1

Length of extra profile 2 from the axis of the anchor bar.

50 mm

Direction of extra profile 2

Option

Description

Default

Type 1

AutoDefaults can change this option.

Type 1

Type 2

Extra profile 1 properties

Option

Description

Default

Hole tolerance

Hole tolerance of extra profile 1.

Same as bolt tolerance

Circular profile height

Height of circular extra profile 1.

 

Profile rotation

Profile rotation of extra profile 1.

Front

Extra profile 2 rotation

Option

Description

Default

Extra profile 2 rotation

Profile rotation of extra profile 2.

Front

General tab

Click the link below to find out more:

General tab

Analysis tab

Click the link below to find out more:

Analysis tab

Quick feedback

The feedback you give here is not visible to other users. We use your comments to improve our content.
We use this to prevent automated spam submissions.
Content rating: 
No votes yet