PEB Anti-sag roof and wall

Last updated November 20, 2017 by Developer TIN

Software version: 
Not environment-specific

PEB Anti-sag roof and wall

PEB Anti-sag roof and wall allows you to create anti-sag members for either roof or wallplate that represents a structure such as a wall or roof panel

In Tekla Structures, a panel is created by picking two or more points.

In cast-in-place concrete the term wall refers to a concept similar to panel.


How to locate

The installers are available at Pre-Engineered Building Tools for Tekla Structures version 21.0 and above.
After the installation the icon shown below is available in the component catalogcatalog that contains all system components and custom components, and the macros and applications



Input for this extension can be:

1. Select purlins or select purlin component, press the middle mouse button to finish selection.
If the input is a purlin component (purlins are part of a component), then inputs 2 and 3 are mandatory. If the input is purlins (two or multiple purlins in the same plane in a bay), then inputs 2 and 3 are optional. Use the Yes / No options to define this.

2. Select the first reference member (reference member can be a component or a beam part).

3. Select the second reference member (reference member can be a component or a beam part).

In case of purlin component input, the anti-sag arrangement bay is defined by reference members, and the length of the bay is calculated from the first reference member part/component center line to the second reference member part/component center line.

In case of individual purlin input, the anti-sag arrangement bay is defined by first purlin start and end, and the length of the span is calculated from the first purlin start to end points.

PEB Anti-sag roof and wall is created with default values.

PEB Anti-sag roof and wall dialog box

The dialog box contains the following tabs:

  1. Picture
  2. Parameters
  3. Parts
  4. Accessories & Assembly


Parallel arrangement

Different sag rod spacings can be achieved using the following options. Spacing references are based on the input selection. If input selection includes refererence members, the references are based on them, otherwise references are the start and end of the first selected purlin.

Option Description
Equally distributes the given number of anti-sag rods in between the references
Allows you to enter a distance list for defining parallel spacing
Allows you to keep a constant distance between anti-sag members. The remaining distance (which is lower than the provided distance) adjusts at both ends.

Thread options

Option Description
Allows you to define a plain rod 

Allows you to define a fully threaded rod. In this case an assembly attribute (SAGROD_THREAD) is updated with value as Full.

Allows you to define a plain rod threaded at the end. In this case an assembly attribute (SAGROD_THREAD) is updated with thread length value.


Rod arrangement

These options enable you to define s rod arranging pattern.

Option Description
Vertical hole pair: Bottom hole to top hole
Vertical hole pair: Top hole to bottom hole
Vertical hole pair:Top to top, bottom to bottom
Vertical hole pair: Bottom to bottom, top to top
Horizontal hole pair: First hole to first, second to second
Horizontal hole pair: Second hole to second, first to first

Vertical hole pair distances from top/ bottom

These are enabled only when the holesmall hollow open throughout a part or assembly that is usually used for fastening parts with bolts or other such objects

Hole is created in the same way as bolts and hole properties are defined in the bolt properties.

pairs are vertical (only for 1 to 4 in the above options). Hole locations from both purlin edges can be defined here.

Hole type

This option is for hole creation type. The options are:

  1. Bolt hole
  2. Part cutcut that is defined by a cutting part

  3. Both (bolt hole and part cut)
  4. No hole (no holes created in this case)

Hole tolerence

Hole tolerence can be adjusted here.

Empty hole in hole pair

Option Description
Creates only required holes.
Creates hole pairs. This is helpful for first and last purlins.

Horizontal hole pairs

These are enabled only when the hole pairs are horizontal (only for 5th and 6th in the rod arrangement pattern options).

Option  Description
Hole spacings are referenced to the first hole of the pair. 
Hole spacings are referenced to the middle of the distance between two holes in the pair. 

Hole pair pitch

Distance between two hole pairs.

Part lengths

Sag rod main part(1) part that exists in a building object and that determines the position number for the assembly or cast unit and the direction of assembly or cast unit drawings

(1) Main part can be an assembly main part or a cast unit main part.

(2) input part that the user selects first when creating a component

(2) Connections and details always have a component main part.

(rod) length can be defined by providing end offsetpart property that is used to move the ends of a part, relative to the part’s reference line

from the part center of purlins, or providing one offset and total rod length. Thickness for washer, nut and lockto prevent unwanted action in a model or a drawing

It is possible to lock model objects, reference models, and drawings, for example.

nut can also be defined from here.


All part properties (profile, prefix, start no, material, name, finish, classpart property that groups parts according to identifiers given by the user

The identifiers of classes are usually numbers. Classes can be used for defining the color of parts in the model, for example. Class does not influence the numbering of model objects.

, note ) can be modified here.

Accessories & assembly

You can control the creation of the parts using the Yes/ No options. Adding the parts in to the assembly can also be controlled using the Yes/No option. If both sides are similar, Same as start option saves time. If both sides are not the same use the Different option to alter the values on other side. 

Assembly name, assembly prefix and assembly start numberfirst number of a numbering series

also can be defined here.


How to make multiple bay anti-sag members if the same purlin component is applicable for multiple bays?

- Select the purlin component, select the reference members for that particular bay. Anti-sag rods will be created for that particular bay. Repeat this for other bays in the same way.

How to skip some purlins in the purlin component from making a sag rod?

-Select the parts and repeat applying the extension for each set of purlins.

Quick feedback

The feedback you give here is not visible to other users. We use your comments to improve our content.
We use this to prevent automated spam submissions.
Content rating: 
No votes yet